Switch to Classic
Models > 10478-2 > Instructions

10478-2 General Electric Range - Instructions

All Instructions for the 10478-2
31 - 39 of 39
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The burner bowls were encrusted with grease and spills.
I easily took out the old ones and put in the new ones sent by Part Select. As promised they fit perfectly. Now when my wife cooks there is no more smoke and it does not set off the smoke detector.
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Ed from Canyon City, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Replaced All Burner Receptacles After One Failed And Also Replaced Ball Burner Bowls
This installation was for a replacement for one of the burner bowls on the original order. Replacement bowl fits proiperly.
Parts Used:
Burner Bowl - 8 Inch
  • ROBERT from MECHANICSBURG, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burner bowls had been used and abused for year gone by in this rental.
Replaced them all. Next I want to replace the burners.
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Diane from Rio Rancho, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Oven Door Handle Broke
The repair was very easy. It did require a very small torx driver (I can't remember the size off hand.) and a 1/4" nut driver.
Parts Used:
Door Handle
  • Heidi from Carrollton, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
bowls were worn out
Open the box and inserted the bowls
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • frances from winston salem, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
uneven heating of oven
This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!
Parts Used:
Oven Sensor
  • John from Sandstone, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
slot that heating element fits was worn down and caused burners to be uneven
replaced with new ones
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Judith from Broadway, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The range kept giving an F2 alarm
When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.
Parts Used:
Oven Sensor
  • Les from Coal Creek, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
6" and 8" burner bowl replacement
Slide out burner elements. Remove old burner bowls. Insert new burner bowls and reinstall burner elements.
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Shawn from Lubbock, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 10478-2
31 - 39 of 39