1039337361 Kenmore Range - Instructions

Mary from Arab, AL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

the drip bowls were worn out

simply replaced them.

Parts Used:

linda from STANTON, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Drip bowl from a big box store was too big even though both say 8”.

Ordered the part and set it in.

Parts Used:

Kathleen from INCLINE VLG, NV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Old Terminal Block was arcing.

Cut Wires to old terminal block and wired in new Terminal Block

Parts Used:

Surface Burner Terminal Block Kit

Robert from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Hanging broiler

Quick and easy, thanks!

Parts Used:

Single Heating Element Support Clip

Doris from Aberdeen, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

broil element blown out

At first I tried to remove the element from the top of the oven. I took out the screws with a nut-driver (1/4"). Them I tried to pull the element out slowly so I could unplug it from the power wires. One of the wires pulled off bfore I could get it out. I then pulled the range out from the wall and removed the back from it. THEN I noticed that if you pull the stove away from the wall first and take off the back the wires are right there and easy to take on and off. Then replace the the back panel, plug in the stove and test the element. It will give off a slight odor as the manufacturing coating is burned off.

Parts Used:

JOHN from AZTEC, NM
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Live in an apartment and they had generic drip pans on the stove causing pots to tilt when cooking.

Replaced drip pans that the apartment Superintendent had in place with the correct drip pans and now cooking is beautiful again! No more uneven cooking on the stove top.

Parts Used:

Jennifer from Cleveland, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Finish coming off of bowls

Removed burner from each one. removed drip bowl. Inserted new bowl. Replaced burner. Excellent help from order people so I got the correct bowl was irreplacable.

Parts Used:

Robert from Ledyard, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burners would not lay flat

Removed the burner elements, removed and disposed of old drip pans, cleaned the area, relaced with new drip pans and replaced the burner elements. Verified all burners were level - good as the day it was new!

Parts Used:

Alfred from Forest, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

8 of 36 people found this instruction helpful.

Was this instruction helpful to you?

Right Front [surface burner terminal block kit]

We did the repair by following the inclosed instructions. we are elderly retired average ages 82. This was our first repair and it went very well. We are so pleased to have saved over $80.00 compared with hired labor 3 yre. ago for the same part. Thanks so much for your good service.

Parts Used:

Surface Burner Terminal Block Kit

Wayne from Montoursville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Broiler Element Burned Out

1)Undid two hex nuts holding broiler element in place. 2)Slipped fasteners off pegs connecting element to oven. 3)Simply reversed the process, when installing new element.

Parts Used:

Arthur from Midlothian, VA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set, Wrench (Adjustable)

Was this instruction helpful to you?

Clips needed to re attach heating element

Pulled out old with pliers. Twisted new clips in per instructions.

Parts Used:

Single Heating Element Support Clip

Dennis from Orlando, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

broiler element burned out

shut off power to range, removed old element, looked up part on line, shopped for best price, Part select was $30 less than sears replacement part, ordered part, part arrived in 4 days, installed new part and I was broling again.

Parts Used:

daniel from fort mill, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Drawer guide

Used Phillips screw driver, installed guide, applied lubricant.

Parts Used:

Rear Drawer Glide

Lee from Grass Valley, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Finding a drip pan that fit so that pots could sit level.

Ordered the drip pan from ParSelect.com. Unplugged element and took out old pan. Placed new pan in and replaced element. For the first time in many years, the part fit.

Parts Used: