030212 - Overview
Models starting with 030212
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Grommet
PartSelect #: PS9294797
Manufacturer #: 692189
This OEM grommet, also called a 90-degree breather tube, is sold individually. Black in color and made of rubber, this is a 90-degree elbow for the crankcase breather tube of your mower engine. If you...
$6.25
In Stock
Carburetor Rebuild Kit
PartSelect #: PS8983479
Manufacturer #: 495606
This is the replacement carburetor kit for your small engine, used for outdoor power equipment. The carburetor rebuild kit includes the float, needle, gaskets, and seals that you need to refurbish you...
$46.05
On Order
Grommet
PartSelect #: PS9064851
Manufacturer #: 692187
This grommet is an OEM part that is a 45-degree elbow for the crankcase breather tube of your mower engine. That is why it is also known as a 45-degree breather tube.
The part is made of rubber and ...
$6.25
In Stock
Gasket-fuel Tank
PartSelect #: PS9294811
Manufacturer #: 692241
Genuine OEM replacement part used on a variety of Engines. This part provides an air tight seal for mounting the Gas Tank. This Gasket is made out of Composite Material and it is Sold Individually. Ov...
$6.25
In Stock
Clutch-starter
PartSelect #: PS8968281
Manufacturer #: 399671
Discover the power of optimal engine performance with the Briggs and Stratton Starter Clutch. A vital piece of your garden equipments engine, this starter clutch engages your machines flywheel while k...
$46.98
In Stock
Gasket-breather
PartSelect #: PS8943888
Manufacturer #: 27549S
The Breather Gasket is OEM and used to provide an airtight seal for the breather assembly. It is a gray part, attached between the breather cap and engine. Installation is rated "Easy" and will requir...
$6.25
In Stock
Cap-fuel Tank
PartSelect #: PS11961623
Manufacturer #: 494559
This is a genuine manufacturer-approved replacement part that is specially produced for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It is designed to kee...
$16.96
Special Order
Screw
PartSelect #: PS9294686
Manufacturer #: 691640
This is a genuine OEM sourced part which is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is a standard hardware which may have multip...
$6.25
In Stock
Gasket-cyl Hd
PartSelect #: PS9295154
Manufacturer #: 698717
This item is a genuine Briggs & Stratton part that has been sourced from the original manufacturer and is intended to be used with small engines. The gasket is used to seal the connection between the ...
$7.67
In Stock
Armature-magneto
PartSelect #: PS9035906
Manufacturer #: 591420
This replacement armature-magneto is specially designed for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It is an authentic part sourced directly from ori...
$61.15
In Stock
Cap-spring
PartSelect #: PS9294523
Manufacturer #: 690766
It is an OEM component which is designed for Briggs and Stratton engines that are commonly installed on a variety of lawn and garden equipment. The cap helps to secure the spring in the pump. Over tim...
$6.25
In Stock
Exact Part matches for your search term
[Viewing 1 of 1]
Base Unit with No Plates
This part number matches the current model number 030212
PartSelect #: PS10507584
Manufacturer #: 030212
$279.95
Special Order
Common Symptoms of models starting with 030212
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Could not keep an aftermarket muffler on the engine.
Once I determined what OEM muffler I needed, installation was relatively easy. I have a 1982 4hp Briggs on my Snapper tiller. There was a 90* galvanized elbow coming out of the exhaust port, with a bezel nut to lock it down. Do not remove the elbow, even though it appears that you should. If you install the muffler without the elbow the m
... Read more
uffler will parallel the the vacuum for the carburetor and can melt the rubber couplers. Use the elbow to direct the heat away from the carburetor. Use a pipe wrench to lock down the bezel nut because the weight of the muffler, especially under vibration, can work loose and fall down on the tine belt cover and melt it. The bezel nut that comes with the muffler should also be used to lock down the muffler to the threaded intake bracket that comes with the muffler, not to replace the bezel nut for the elbow.
Read less
Parts Used:
-
Richard from KERNERSVILLE, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
13 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old diaphragm dried up
Tore carburetor off leaf blower and replaced. To do that require taking off the air cleaner removing the gas tank and all the brackets holding the controls on it. And keeping track of all the screws and Wires that control choke and throttle. I took several photographs. I did not need all the gaskets and jet’s that were included in the ki
... Read more
t but it had what I needed.
Read less
Parts Used:
-
Steven C from CENTREVILLE, MI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
6 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!