Husqvarna Snow Blower Hardware
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Husqvarna Snow Blower Hardware
Your Price
$6.40
In Stock
Husqvarna Snow Blower Lawn Mower Ring Clip
PartSelect Number PS9143890
Manufacturer Part Number 812000029
The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle.
This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.
Installation Instructions
Anthony from OLIVEHILL, TN
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Read more...
Your Price
$7.04
In Stock
Husqvarna Snow Blower Lawn Mower Mandrel Spacer Washer
PartSelect Number PS9286886
Manufacturer Part Number 532187690
An OEM part sourced directly from the manufacturer, this part is sold individually. Washers help to spread the load, and prevent damage to the surface being fixed, or provide some sort of insulation such as electrical. Washers can also be important for preventing galvanic corrosion. This specific washer is commonly used with outdoor lawn equipment, and is compatible with the mowers and tractors that are listed below.
Your Price
$6.40
In Stock
Husqvarna Snow Blower Lawn Mower Hardened Washer
PartSelect Number PS9015920
Manufacturer Part Number 532188967
This OEM hardened washer spreads load under the bolts of your lawn tractor. It is silver, made of metal, and is sold individually. Over time, the washer may become damaged due to wear and fatigue, and will need to be replaced. You may notice this part is damaged if you start hearing a grinding or rubbing noise between the tire rim and ring clip.
You will need a pair of needle nose pliers to carry out this repair, which our customers generally found easy.
You will locate the washer on the spindle, between the wheel and the ring clip.
Your Price
$6.40
In Stock
Husqvarna Snow Blower Lawn Mower Flangelock Hex Nut
PartSelect Number PS9022497
Manufacturer Part Number 532409149
Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To replace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.
Your Price
$6.40
In Stock
Husqvarna Snow Blower Carriage Bolt
PartSelect Number PS16381841
Manufacturer Part Number 596136401
Genuine Manufacturer Approved Carriage Bolt is a standard part that fits a variety of products. This part is sold individually and the Nut is not included. The square area under the head is designed to fit into a square hole in the workpiece. It is this square hole that restrains the bolt and keeps it from turning when the nut is tightened.
Your Price
$6.40
In Stock
Husqvarna Snow Blower Washer 5/16 Std Flt
HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
PartSelect Number PS16381824
Manufacturer Part Number 596134901
It is an authentic item that is supplied directly from the original equipment manufacturer for use with Husqvarna and Poulan lawn and garden equipment. A washer is generally utilized to provide a tight seal between connected parts, over time it may wear out or simply get lost eventually requiring a replacement. Please make sure to check the appropriate diagrams of your specific model for the correct location and application of this hardware. Keep in mind this durable metal washer is sold individually.
Installation Instructions
robert from EUREKA, CA
transaxle rotated forward on 2015 Husqvarna YT42DXLS
2015 Husqvarna YT42DXLS. Both transaxle support struts broke causing the transaxle rotated forward and shear transaxle mounting bracket. The transaxle was not damaged. All 3 parts required replacement. There are some good youtube videos to watch to show how to complete the repair. HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
Your Price
$6.40
In Stock
Husqvarna Snow Blower Nut Lock
PartSelect Number PS16381792
Manufacturer Part Number 596040501
This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.
Your Price
$6.40
In Stock
Husqvarna Snow Blower Hex Head Screw 3/8-24x1-3/8 Gr. 8
PartSelect Number PS9026163
Manufacturer Part Number 532851084
This is a genuine manufacturer-sourced replacement screw which is specially designed for use with Craftsman lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please refer to the appropriate diagrams for the correct location and use of this item. This part is made of high-quality metal and it is sold individually, you will need a wrench to secure or remove it.
Your Price
$8.55
In Stock
Husqvarna Snow Blower Lawn Mower Handle Bolt
PartSelect Number PS9014802
Manufacturer Part Number 532191574
This Handle Bolt is sourced directly from the original equipment manufacturer for use in various lawn and garden equipment. It is used to secure the upper and lower handles together and is tightened by a knob on the other end. It is made of metal, is black, and is sold individually, not as part of a kit or assembly.
This part will need to be replaced when it is worn or damaged and can no longer secure the arms together. No tools are needed to complete this repair.
Customers rated this repair as Easy.
Your Price
$6.40
In Stock
Husqvarna Snow Blower Lock Washer
PartSelect Number PS16381888
Manufacturer Part Number 596238701
This is a genuine OEM replacement part used on a variety of Lawn and Garden Equipment. This part is made out of Metal and it is Sold Individually. This steel washer has several applications based on your unit. Please refer to diagrams for proper application.
Related Husqvarna Snow Blower Parts
- Husqvarna Snow Blower Augers
- Husqvarna Snow Blower Bearings
- Husqvarna Snow Blower Belts
- Husqvarna Snow Blower Brackets and Flanges
- Husqvarna Snow Blower Carburetors
- Husqvarna Snow Blower Deflectors and Chutes
- Husqvarna Snow Blower Engines
- Husqvarna Snow Blower Handles
- Husqvarna Snow Blower Hoses and Tubes
- Husqvarna Snow Blower Knobs
- Husqvarna Snow Blower Lights and Bulbs
- Husqvarna Snow Blower Pulleys
- Husqvarna Snow Blower Seals and Gaskets
- Husqvarna Snow Blower Springs and Shock Absorbers
- Husqvarna Snow Blower Starters
- Husqvarna Snow Blower Transmissions and Clutches
- Husqvarna Snow Blower Wheels and Rollers