Husqvarna Edger Hardware
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Husqvarna Edger Hardware
Your Price
$6.72
In Stock
Husqvarna Edger Lawn Mower Flangelock Hex Nut
PartSelect Number PS9022497
Manufacturer Part Number 532409149
Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To replace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.
Your Price
$6.72
In Stock
Husqvarna Edger Washer 5/16 Std Flt
HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
PartSelect Number PS16381824
Manufacturer Part Number 596134901
It is an authentic item that is supplied directly from the original equipment manufacturer for use with Husqvarna and Poulan lawn and garden equipment. A washer is generally utilized to provide a tight seal between connected parts, over time it may wear out or simply get lost eventually requiring a replacement. Please make sure to check the appropriate diagrams of your specific model for the correct location and application of this hardware. Keep in mind this durable metal washer is sold individually.
Installation Instructions
robert from EUREKA, CA
transaxle rotated forward on 2015 Husqvarna YT42DXLS
2015 Husqvarna YT42DXLS. Both transaxle support struts broke causing the transaxle rotated forward and shear transaxle mounting bracket. The transaxle was not damaged. All 3 parts required replacement. There are some good youtube videos to watch to show how to complete the repair. HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
Your Price
$6.72
In Stock
Husqvarna Edger Nut Lock
PartSelect Number PS16381792
Manufacturer Part Number 596040501
This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.
Your Price
$6.72
In Stock
Husqvarna Edger Lock Washer
PartSelect Number PS16381888
Manufacturer Part Number 596238701
This is a genuine OEM replacement part used on a variety of Lawn and Garden Equipment. This part is made out of Metal and it is Sold Individually. This steel washer has several applications based on your unit. Please refer to diagrams for proper application.
Your Price
$6.72
In Stock
Husqvarna Edger Bolt
PartSelect Number PS16381724
Manufacturer Part Number 595901601
This is a genuine OEM replacement part that is used for lawn mowers and tractors across a number of brands. This is standard hardware which has multiple applications based on your tool. Please refer to diagrams for proper application. It is made out of metal and it is sold individually. You would need a wrench to remove or install this bolt.
Your Price
$6.72
In Stock
Husqvarna Edger Locknut
PartSelect Number PS16382003
Manufacturer Part Number 596322601
This hardware is an authentic OEM sourced item. It is a specially manufactured for use with lawn and garden equipment. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This part has multiple applications depending on the equipment. Please always check appropriate diagrams for correct location and use of this item. Please note, it is sold individually. You will need a wrench to secure or remove this nut.
Your Price
$6.72
In Stock
Husqvarna Edger Lawn Tractor Screw
PartSelect Number PS16575297
Manufacturer Part Number 596039001
It is a genuine replacement screw which is supplied by the original equipment manufacturer, it is specially produced for use with lawn and garden equipment. This is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for the correct location and use of this part. It is a high-quality Pan Head Phillips screw which is made of durable metal and it is sold individually.
Your Price
$6.72
In Stock
Husqvarna Edger Flange Nut
PartSelect Number PS8990057
Manufacturer Part Number 503220001
Genuine Husqvarna replacement part, this item is sold individually. This part is used on all of the Husqvarna Chainsaws listed below. The purpose of this nut is to attach the Clutch Cover along with the Chainsaw bar.
Your Price
$6.72
In Stock
Husqvarna Edger Hex Nut
PartSelect Number PS16382139
Manufacturer Part Number 596583702
This genuine manufacturer sourced replacement part designed for use with lawn mowers. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This is standard hardware which has multiple applications based on your tool. Please refer to diagrams for proper use. This lock nut is made out of metal and it is sold individually. Would require a wrench to remove or install this hex nut.
Your Price
$8.98
In Stock
Husqvarna Edger Lawn Mower Screw
PartSelect Number PS9142752
Manufacturer Part Number 817000616
It is a genuine OEM sourced replacement screw which is specially designed for use with Husqvarna, Poulan and Ryobi riding lawn mowers and garden tractors. This item is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for the correct location and use of this item. It is a high-quality hex head screw which is made of durable metal and it is sold individually.
Related Husqvarna Edger Parts
- Husqvarna Edger Bearings
- Husqvarna Edger Brackets and Flanges
- Husqvarna Edger Caps and Lids
- Husqvarna Edger Carburetors
- Husqvarna Edger Control Cables
- Husqvarna Edger Engines
- Husqvarna Edger Filters
- Husqvarna Edger Handles
- Husqvarna Edger Hoses and Tubes
- Husqvarna Edger Ignitions
- Husqvarna Edger Knobs
- Husqvarna Edger Seals and Gaskets
- Husqvarna Edger Springs and Shock Absorbers
- Husqvarna Edger Starters
- Husqvarna Edger Transmissions and Clutches
- Husqvarna Edger Wheels and Rollers