Hedge Trimmer Filters

Shop By Brand

Popular Hedge Trimmer Filters

Your Price
$3.47
  In Stock
Engine Fuel Filter
★★★★★
★★★★★
(2)
PartSelect Number PS9285148
Manufacturer Part Number 530095646
This fuel filter is for lawn and garden equipment engines. Fuel filter cleans the fuel before it reaches the carburetor. Work in a well-ventilated area when installing this part. Drain the fuel tank and disconnect the spark plug wire before beginning the repair.
Fixes these symptoms
Installation Instructions
Mark from LYNDONVILLE, NY
Deterioration of fuel line system
Removed the top cover (T25 torx), and side cover (T25 torx) with recoil starter. Drained all fuel, and removed all pieces of fuel old fuel line and the weighted filter from inside the tank by shaking out and the (long forceps). A spot headlamp makes it easier to see inside the tank for much of the procedure. Remove the foam filter to find the two 8mm nuts and remove the air filter housing and carburetor (nut driver, 8mm socket) the choke lever slides out of its slot with some wiggling and moving the carb back off the mounting studs. Leave the throttle cable attached to the filter housing and move both assemblies out of the way to access the top wall of the fuel tank. There is a cover over the carb adjust screws that wiggles out also. The fuel line and purge line both pass through the wall of the tank and need to be pulled out with some effort (long curved forceps) from inside the tank through the fuel fill port. They are a tight fit. Pay attention to the lines size and location. Large line is in the position away from the recoil starter with the little plastic fitting hanging near the top of the tank. The smaller line is closest to the recoil starter. Both new lines will need to pass through the tank wall (this is the most difficult part). To facilitate the initial entry through the wall of the tank, cut a tapered end on your new lines. Use a very slippery lube to coat the end of the line and push it into the tank as far as you can from the top (forceps or soft grip pliers) help. Look inside the tank and pull the lines through fully out of the tank fill (long curved forceps and head spot light). Don't pull all the way through the fuel fill, just enough to install the new fuel line fitting in the return purge line and the new weighted filter on the fuel line and pull the lines back inside the tank. The return line with fitting close to the top of the tank and the filter hanging so it lays at the bottom of the tank, and able to swing around so it keeps contact with fuel at all times. Remove the old purge/primer bulb two screws (Phillips). The short stem is suction, long stem is pressure. Don't mix them up and connect lines backwards, don't ask me how I know! Lol! If you have such a saw like mine, that has no fuel lines intact, it is difficult to vision the line routes. There are helpful schematics on the internet. Just remember that the purge bulb long fuel stem sends pressure back to the tank through the return line (larger line in the tank with the line fitting away from the recoil). That line can now be cut to length and pushed on the bulb long stem. The suction side of the bulb short stem, connects to the purge line on the side of the carburetor (short line). You need to cut that line to the same length as the old one. It has to curve twice to get to the suction side of the purge bulb without kinking. The only other line left is the fuel line with the filter attached hanging inside the tank. Be sure you have the filter able to lay on the floor of the tank and move around. That line connects to the carburetor opposit side from the purge bulb. Dont cut that one until the carb is installed for proper length. The fuel routes from that filtered line into the carb, then out of the carb to the purge bulb suction side, then out to the return line in the tank with the fitting end. That fitting installed into the line serves only to keep the line from pulling back out of the tank, nothing attaches to it. Make sure all lines are clear of the mounting area of the carb, and throttle function. Pass the bulb lines through the slot in the side of the case being sure the lines don't kink. Secure the bulb with the two phillips screws. Position the carb on the studs and slide the choke lever into its place in the case as you go. Place the filter housing on the studs and push the carb and housing down watching the fuel lines for any kinks, especially where the throttle cable is in close proximity to the short carb purge line. Check the throttle function for interferance, and Install the two 8mm nuts. Now route the fuel line around the throttle mechanism out of the way, hold it to the barb on the side of the carb and cut it to length and install. Put some fuel mix in the tank (dont fill it) to test. Press the primer bulb, tilting the saw with fill cap removed, and see if anything leaks, also watch fuel flow back to the tank inside as you press the bulb. You should see fuel and air bubbles from the purge line. When all air bubbles are gone the system is purged. Install the new foam filter in the housing and then the top and side cases. I did not reinstall the cover of the carb adjust needle screws so I could adjust the fuel/ air mixture to run at peak performance. Hope this helps! The kit that I got was perfect and there are some useful instructions included. Thank you! Respectfully Mark Read more...
Your Price
$6.06
  In Stock
Air Filter
★★★★★
★★★★★
(7)
PartSelect Number PS9195232
Manufacturer Part Number A226001410
This part is the replacement air filter for your small engine, used for outdoor power equipment. It has a black plastic rim that is approximately 2.5 inches by 2.5 inches. The air filter in your small engine prevents dirt and debris from entering the cylinder, where it can cause more serious damage. If your air filter is clogged, it can decrease your engine performance, and it will need to be cleaned or replaced. If the filter is damaged, it will need to be replaced as well. This is an OEM part sourced directly from the manufacturer, and is it sold individually.
Installation Instructions
Paul from SENECA, SC
Fuel line grommet rotted
This blower is quite old looked on YouTube. Removed grommet with needle nose pliers. Removed tank to install new parts. I had trouble getting return line off carb so planned to reuse it after grommet was in place. Thin was a mistake because the seated grommet compresses the holes. Took unnecessary time to get it through. With my trimmer with all lines in place. Hardest part was to get the grommet to seat even with silicone. Read more...
Your Price
$3.47
  In Stock
In-Tank Fuel Filter
★★★★★
★★★★★
(2)
PartSelect Number PS9971445
Manufacturer Part Number 530095646
Fixes these symptoms
Your Price
$5.94
  In Stock
Filter-Air
PartSelect Number PS8862436
Manufacturer Part Number 13031051830
Your Price
$5.79
  In Stock
Air Filter (Ready-Oiled)
PartSelect Number PS9020811
Manufacturer Part Number 537186301
This ready-oiled air filter is an OEM part that traps dirt and debris, preventing them from entering the engine. This part is black, comprised of foam, and is sold individually. Your air filter may become dirty and clogged over time, and because it is oiled, it is difficult to wash because it is oiled, so it will need to be replaced. A clogged air filter will cause your engine to run rough from restricted air flow. This is an easy repair to make and does not require any special tools.
Your Price
$9.42
  In Stock
Case-Air Cleaner
PartSelect Number PS9231805
Manufacturer Part Number P021012870
Your Price
$4.08
  In Stock
Filter-Air
PartSelect Number PS8862431
Manufacturer Part Number 13031004560
Your Price
$5.79
  In Stock
Air Filter
PartSelect Number PS9022665
Manufacturer Part Number 537143101
This air filter comes in black foam and is rated as "Easy" to install. Installation requires a screwdriver, and the part attaches inside of the air cleaner housing. This manufacturer certified filter is used to prevent dirt and debris from entering the carburetor and engine, which would cause damage. If broken or clogged, the engine will experience performane issues or may not turn on. If broken, the filter should be replaced. Tip: Put a bit of two-cycle oil in the bag and let it absorb into the filter. This makes it more tacky to catch debris.
Your Price
$10.30
  In Stock
Air Cleaner Case Asy
PartSelect Number PS9235482
Manufacturer Part Number P021002921
Your Price
$6.95
  In Stock
Air Filter
PartSelect Number PS8993617
Manufacturer Part Number 502198602

Brands