Engine Engines

Engine Camshaft This is a genuine Toro replacement part. The camshaft is designed by the manufacturer for use in lawn tractors and engines. This part is made of metal, and is placed in the crankcase assembly to interact with the crankshaft. It comes with two metal tappet valves. You may require a wrench when replacing this item. This part is sold individually.

Engine Friction Ring This friction ring is an authentic item which is supplied by the original manufacturer for Toro lawn mowers. It is one of the special parts that helps to provide a tight seal between components. Over time it may wear out, get damaged or simply lost eventually requiring a replacement. This high-quality friction ring is made of a durable material and is sold as an individual component. Note, you may need a wrench set to remove and resecure the hardware that holds this part. Check the diagrams of your specific model for the exact location and the correct application of this hardware.

Engine Oil Kawasaki 10W-40 4-Cycle Oil. Kawasaki KTECH 4-cycle oil is enhanced with Anti-Foaming and Anti-Sheer agents, along with other additives.

Engine Rod-push

★★★★★

★★★★★

2 Reviews

This is an Genuine OEM replacement part used on a variety of Lawn and Garden Engines. This part is made out of Metal and it is sold individually. The Push Rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent pushrod can not only affect your engine's performance, it can seriously damage other parts if the problem is not taken care of immediately.

Engine Push Rod This replacement push rod is specially designed for Kawasaki engines. It is an authentic high quality item that is sourced from original equipment manufacturer. The rod rides is attached to the camshaft to push the exhaust valve open during the exhaust stroke. A bent pushrod can not only affect your engine's performance, but it can also seriously damage other parts if the problem is not taken care of immediately. Please note this metal push rod is sold individually.

Engine Piston Ring This piston ring is an authentic manufacturer approved replacement part. Is is commonly used on Echo gas trimmers/edgers. The purpose of a piston ring is to create an air tight seal inside the cylinder. A worn or broken piston ring will allow combustion gases to escape the seal and enter the crankcase. This would cause low compression and a loss of power. Replacing an o-ring should resolve this issue. This part is made out of metal and is sold individually. To complete this repair you will need a set of wrenches, pliers and a screwdriver. • Remove the air cleaner • Drain the fuel • Remove the air cleaner case • Remove the carburetor • Remove the intake insulator • Remove the spark plug • Remove the engine cover • Remove the insulator gasket • Remove the starter assembly • Remove the fuel tank • Remove the air duct • Separate the engine • Bind the engine • Remove the clutch • Remove the flywheel • Remove the starter pulley • Unbind the engine • Remove the muffler • Separate the cylinder from the crankcase • Remove the piston ring • Install the piston ring • Reassemble and test the equipment

Engine Rod-push This replacement push-rod is a genuine manufacturer supplied item that is specially designed for Briggs and Stratton engines. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent push rod can seriously affect your engine's performance and it damage the engine if the problem is not taken care of immediately. This part is made out from durable aluminum and it is sold individually.

Engine Rod-push This replacement push rod is specially designed for use on Briggs and Stratton engines. It is an authentic part supplied directly from original equipment manufacturer. The push rod is connected to the camshaft to push the exhaust valve open during the exhaust stroke. A bent rod can not only affect your engine's performance, it can seriously damage other parts if the problem is not taken care of immediately. Please note, this assembly includes the (1) push rod and (1) tappet valve.

Engine Push Rod This is an genuine OEM replacement part used on Kawasaki engines. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent pushrod can not only affect your engine's performance, it can seriously damage other parts if the problem is not taken care of immediately. This part is made out of metal and it is sold individually.

Engine Oil Honda engine oil, SAE 10W-30, One quart