Craftsman Snow Blower Transmissions and Clutches

Your Price

$34.44

Craftsman Snow Blower Wheel Friction 4.3 Ru

★★★★★

3 Reviews

PartSelect Number PS9263021

Manufacturer Part Number 1501435MA

This is an original part from Craftsman for use with Craftsman Snowblowers. The fiction wheel assembly meshes with the friction disc, causing the drive wheel axle to turn. The most common reason for replacing the friction wheel is when the snowblower's wheels don't turn.This part is sold individually. Disconnect the spark plug wire before installing this part. The tools that you will need to replace the friction wheel disc are 3/8" socket, 9/16" socket, adjustable wrench, hammer, 1/2" socket, flat-head screwdriver, and lubrication.

Fixes these symptoms

Drive system does not work
See more...

Installation Instructions

Kenneth from ALDAN, PA

Refurbishing for next winter season

I replaced the auger belt and drive belt by separating the machine. The auger belt alone can be replaced by simply tilting without separating but the drive belt can not. So after separating the machine, I removed the auger belt by loosening the belt guide and removing the tensioner. I then loosened the nut that secures the drive wheel. This gave me enough play to remove the drive belt from the drive tensioner and then wiggle it from the drive wheel and out of the machine. Install by wiggling the belt back behind the drive wheel until you can slip it on the wheel. pull tensioner pulley out of the way to get the belt on the top pulley. Tighten the nut to secure the drive wheel. Reconnect the machine at the bottom of the auger housing and replace the auger belt, tensioner, and belt guide. Complete by replacing the upper bolts that hold the two parts together. I have not replaced the friction wheel as of yet. My process took 30 - 45 minutes for both belts. Read more...

Your Price

$22.79

Craftsman Snow Blower Wheel-friction 4.

★★★★★

1 Review

PartSelect Number PS9311064

Manufacturer Part Number 935-0243B

This item has been sourced from the original manufacturer to be used with snowblowers from MTD, Ryobi, Yard Machines, Bolens, and Yard-Man. This item is the hard rubber tire that fits onto the friction wheel and is used to rotate the friction disc. Overtime this item can wear down and need to be replaced to make good contact with the friction disc. This item is available as an individual replacement part.

Fixes these symptoms

Drive system does not work
See more...

Your Price

$61.58

Craftsman Snow Blower Worm Gear

PartSelect Number PS9165943

Manufacturer Part Number 917-04861

This is a worm gear that is designed for use within a variety of snowblowers and snowblower tractor attachments. The worm gear is used to rotate the auger through the drive mechanism, also known as the transmission. Featuring an approximately 2-inch diameter, this worm gear is made of high-quality, durable metal and is sold as an individual part. The worm gear will likely be secured in place using bolt or other fastener, and replacing this gear will require a wrench set and screwdriver. Make sure to check any user manuals or diagrams for exact placement of the worm gear within your snowblower.

Your Price

$152.99

Craftsman Snow Blower Gearbox Asm-chut Rota

PartSelect Number PS11813283

Manufacturer Part Number 918-04801B

This is an authentic replacement part that is OEM sourced to be used with snowthrowers from MTD, Yard Machines, Troy-Bilt, and Yard Man. The gearbox is actuated by the chute control motor and used to rotate the chute to guide the direction of the snow discharge. This item is available as an individual replacement part.

Installation Instructions

Ralph from SALT LAKE CTY, UT

The chute rotation assembly was stuck

I ordered a replacement chute rotation gearbox. The small metal ball on the end of the cable (on the replacement part) was attached about 1/8" too long and made it so that there was too much play in the trigger that operates it. Thus, the replacement part did not work. I called customer service for directions about returning the part. They said it must have been defective. I'm still waiting for instructions about returning it for a refund. The whole thing was a bust. I ended up disassembling the old gearbox and fixing it, instead of replacing it (which would have been my preference). The replacement part did not work at all! Read more...

Your Price

$98.10

Craftsman Snow Blower Gear Worm

PartSelect Number PS8997773

Manufacturer Part Number 51405MA

This is an authentic OEM sourced part which is specially designed for use with Craftsman snowblowers. It is an identical replacement for a missing or faulty worm gear that helps to drive the auger shaft and has a key slot in the arbor to fit onto the output shaft using a woodruff key which is sold separately. Keep in mind this high-quality component is made of durable metal and is sold individually. Please make sure to check the appropriate diagrams of your model for the correct location and application of this part.

Your Price

$18.28

Craftsman Snow Blower Wormgear Chute Rotate

PartSelect Number PS9035829

Manufacturer Part Number 585196MA

This is a genuine OEM sourced part is specially designed for Murray snowthrowers. It attaches inside the worm gear bracket and moves the chute when the handle is rotated. Over time it may wear out and begin to fail eventually requiring a replacement. Make sure to refer to the owner's manual and the appropriate diagrams for your model to ensure the correct repair procedure. Note, this high-quality gear-worm is made of durable metal and is sold as an individual component. A wrench set will be needed to perform the replacement.

Your Price

$488.12

Craftsman Snow Blower 26'' Auger Gearbox Assembly

PartSelect Number PS11813273

Manufacturer Part Number 918-04172C

Your Price

$457.58

Craftsman Snow Blower Gearbox Asm-auger

PartSelect Number PS11813272

Manufacturer Part Number 918-04171C

Your Price

$34.70

Craftsman Snow Blower Case Gear Lh 10aug/9i

PartSelect Number PS8830296

Manufacturer Part Number 10576MA

This (left hand) gear case is supplied directly from the original equipment manufacturer. Constructed of durable metal, the gear case is made for use with many snowthrower machines. This item is secured onto the right hand gear case, through the shaft auger output. The gear case is designed to protect the inner gears and components, as well as securing necessary lubricants. Wrench and socket sets are needed in making the proper installation. Please refer to the specific manual for repair instructions. This part is sold individually.