My Orders
Craftsman Snow Blower Control Cables
GET YOUR OFFICIAL Craftsman PARTS TO ENSURE VICTORY
Shop By Part Type
View MorePopular Craftsman Snow Blower Control Cables
This is a genuine replacement clutch cable sourced from the original equipment manufacturer, designed for use with MTD and Yard Man snowblowers. It serves as an identical replacement for a missing or damaged cable originally installed on new units and plays a vital role in engaging the auger for proper snowblower operation. Made with high-quality rubber insulation, this durable component is sold individually. Please note that the housing, trigger, and hardware are not included and must be purchased separately. For proper installation, refer to your model’s diagram, and be prepared to use tools such as pliers and a wrench set.
This is a genuine replacement clutch cable sourced from the original equipment manufacturer, designed for use with MTD and Yard Man snowblowers. It serves as an identical replacement for a missing or damaged cable originally installed on new units and plays a vital role in engaging the auger for proper snowblower operation. Made with high-quality rubber insulation, this durable component is sold individually. Please note that the housing, trigger, and hardware are not included and must be purchased separately. For proper installation, refer to your model’s diagram, and be prepared to use tools such as pliers and a wrench set.
This speed selector cable is sourced from the original manufacturer and consists of a cable enclosed in an outer protective casing. It connects the control panel to the transmission/drive system of the snow blower, allowing you to adjust and select the speed at which the snow blower moves. When you adjust the speed on the control panel, the cable is activated, and it engages with the transmission to control the snowblower. The speed selector cable can fail over time due to various reasons including fraying from use and exposure to harsh conditions, corrosion, or inadequate lubrication, which causes it to become stiff. If the cable is faulty, your equipment will be unable to move, or stuck at one speed, and the control panel may be unresponsive. Disconnect the faulty cable and route the new cable through the same path. Connect the cable to the control panel and transmission, and secure it with the appropriate fasteners.
This speed selector cable is sourced from the original manufacturer and consists of a cable enclosed in an outer protective casing. It connects the control panel to the transmission/drive system of the snow blower, allowing you to adjust and select the speed at which the snow blower moves. When you adjust the speed on the control panel, the cable is activated, and it engages with the transmission to control the snowblower. The speed selector cable can fail over time due to various reasons including fraying from use and exposure to harsh conditions, corrosion, or inadequate lubrication, which causes it to become stiff. If the cable is faulty, your equipment will be unable to move, or stuck at one speed, and the control panel may be unresponsive. Disconnect the faulty cable and route the new cable through the same path. Connect the cable to the control panel and transmission, and secure it with the appropriate fasteners.
A snow blower that will not change speed or shift between forward and reverse may have a stretched, frozen, or broken control cable. This replacement cable links the operators speed lever to the ground-drive mechanism. Inspect the lever, cable mounts, linkage, belt, and friction drive before deciding the cable has failed. Verify the equipment model because cable length and end fittings must match exactly. Before service, shut off the engine, remove the key, and disconnect the spark plug wire. Note the original cable path, secure each end correctly, keep it away from hot or moving pieces, and test every drive position after adjustment.
A snow blower that will not change speed or shift between forward and reverse may have a stretched, frozen, or broken control cable. This replacement cable links the operators speed lever to the ground-drive mechanism. Inspect the lever, cable mounts, linkage, belt, and friction drive before deciding the cable has failed. Verify the equipment model because cable length and end fittings must match exactly. Before service, shut off the engine, remove the key, and disconnect the spark plug wire. Note the original cable path, secure each end correctly, keep it away from hot or moving pieces, and test every drive position after adjustment.
This is an authentic OEM sourced replacement part designed for use with snow throwers/blowers. It allows you to engage and disengage the unit. This cable is sold individually. You may need pliers to complete this repair. • Remove the cable end from the control head and install the new one • Now you can run the new cable down to the control handle • Attach the other end of the cable • Tie the cable in place just as the old one was, but leave enough clearance and free play to avoid over-bending and breaking the new cable
This is an authentic OEM sourced replacement part designed for use with snow throwers/blowers. It allows you to engage and disengage the unit. This cable is sold individually. You may need pliers to complete this repair. • Remove the cable end from the control head and install the new one • Now you can run the new cable down to the control handle • Attach the other end of the cable • Tie the cable in place just as the old one was, but leave enough clearance and free play to avoid over-bending and breaking the new cable
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This cable barrel holder is a genuine OEM part that is designed for use with tillers and snow throwers. Sold as an individual part, this holder measures approximately 1-inch in length and is used to secure the clutch control handle and cable together. This holder is made of durable plastic and can replace the old holder by simply removing it, inserting the cable into the new holder, and tightening it until it is locked in place.?
This cable barrel holder is a genuine OEM part that is designed for use with tillers and snow throwers. Sold as an individual part, this holder measures approximately 1-inch in length and is used to secure the clutch control handle and cable together. This holder is made of durable plastic and can replace the old holder by simply removing it, inserting the cable into the new holder, and tightening it until it is locked in place.?
It is a genuine part that is supplied by the original equipment manufacturer for use with snowthrowers. This special dual cable fitting helps to secure the control cables on the handle. It is a high-quality replacement for a damaged or a missing component that was installed on a new unit. One durable plastic fitting is included. To ensure the exact location and the correct application of this part, refer to the appropriate diagrams for your model. It is secured to the handle by a screw which is sold separately. Note, a screwdriver will be needed to perform this repair.
It is a genuine part that is supplied by the original equipment manufacturer for use with snowthrowers. This special dual cable fitting helps to secure the control cables on the handle. It is a high-quality replacement for a damaged or a missing component that was installed on a new unit. One durable plastic fitting is included. To ensure the exact location and the correct application of this part, refer to the appropriate diagrams for your model. It is secured to the handle by a screw which is sold separately. Note, a screwdriver will be needed to perform this repair.
This is a genuine manufacturer-sourced part which is specially designed for use with Craftsman Snowblowers. The chute control cable guide attaches the chute control cables to the chute control lever and guides each cable as the lever is moved. This part is sold individually. Tools you will need for this repair are Pliers and an Adjustable Wrench.
This is a genuine manufacturer-sourced part which is specially designed for use with Craftsman Snowblowers. The chute control cable guide attaches the chute control cables to the chute control lever and guides each cable as the lever is moved. This part is sold individually. Tools you will need for this repair are Pliers and an Adjustable Wrench.
