Craftsman Blower Parts

Craftsman Appliance Parts

Popular Craftsman Blower Parts

Your Price
$4.99
   In Stock
Craftsman Blower Engine Fuel Filter
★★★★★
★★★★★
2 Reviews
PartSelect Number PS9285148
Manufacturer Part Number 530095646
This fuel filter is for lawn and garden equipment engines. Fuel filter cleans the fuel before it reaches the carburetor. Work in a well-ventilated area when installing this part. Drain the fuel tank and disconnect the spark plug wire before beginning the repair.
Fixes these symptoms
  • Engine stops after a few seconds or minutes
  • Will Not Start
  • See more...
Installation Instructions
Mark from LYNDONVILLE, NY
Deterioration of fuel line system
Removed the top cover (T25 torx), and side cover (T25 torx) with recoil starter. Drained all fuel, and removed all pieces of fuel old fuel line and the weighted filter from inside the tank by shaking out and the (long forceps). A spot headlamp makes it easier to see inside the tank for much of the procedure. Remove the foam filter to find the two 8mm nuts and remove the air filter housing and carburetor (nut driver, 8mm socket) the choke lever slides out of its slot with some wiggling and moving the carb back off the mounting studs. Leave the throttle cable attached to the filter housing and move both assemblies out of the way to access the top wall of the fuel tank. There is a cover over the carb adjust screws that wiggles out also. The fuel line and purge line both pass through the wall of the tank and need to be pulled out with some effort (long curved forceps) from inside the tank through the fuel fill port. They are a tight fit. Pay attention to the lines size and location. Large line is in the position away from the recoil starter with the little plastic fitting hanging near the top of the tank. The smaller line is closest to the recoil starter. Both new lines will need to pass through the tank wall (this is the most difficult part). To facilitate the initial entry through the wall of the tank, cut a tapered end on your new lines. Use a very slippery lube to coat the end of the line and push it into the tank as far as you can from the top (forceps or soft grip pliers) help. Look inside the tank and pull the lines through fully out of the tank fill (long curved forceps and head spot light). Don't pull all the way through the fuel fill, just enough to install the new fuel line fitting in the return purge line and the new weighted filter on the fuel line and pull the lines back inside the tank. The return line with fitting close to the top of the tank and the filter hanging so it lays at the bottom of the tank, and able to swing around so it keeps contact with fuel at all times. Remove the old purge/primer bulb two screws (Phillips). The short stem is suction, long stem is pressure. Don't mix them up and connect lines backwards, don't ask me how I know! Lol! If you have such a saw like mine, that has no fuel lines intact, it is difficult to vision the line routes. There are helpful schematics on the internet. Just remember that the purge bulb long fuel stem sends pressure back to the tank through the return line (larger line in the tank with the line fitting away from the recoil). That line can now be cut to length and pushed on the bulb long stem. The suction side of the bulb short stem, connects to the purge line on the side of the carburetor (short line). You need to cut that line to the same length as the old one. It has to curve twice to get to the suction side of the purge bulb without kinking. The only other line left is the fuel line with the filter attached hanging inside the tank. Be sure you have the filter able to lay on the floor of the tank and move around. That line connects to the carburetor opposit side from the purge bulb. Dont cut that one until the carb is installed for proper length. The fuel routes from that filtered line into the carb, then out of the carb to the purge bulb suction side, then out to the return line in the tank with the fitting end. That fitting installed into the line serves only to keep the line from pulling back out of the tank, nothing attaches to it. Make sure all lines are clear of the mounting area of the carb, and throttle function. Pass the bulb lines through the slot in the side of the case being sure the lines don't kink. Secure the bulb with the two phillips screws. Position the carb on the studs and slide the choke lever into its place in the case as you go. Place the filter housing on the studs and push the carb and housing down watching the fuel lines for any kinks, especially where the throttle cable is in close proximity to the short carb purge line. Check the throttle function for interferance, and Install the two 8mm nuts. Now route the fuel line around the throttle mechanism out of the way, hold it to the barb on the side of the carb and cut it to length and install. Put some fuel mix in the tank (dont fill it) to test. Press the primer bulb, tilting the saw with fill cap removed, and see if anything leaks, also watch fuel flow back to the tank inside as you press the bulb. You should see fuel and air bubbles from the purge line. When all air bubbles are gone the system is purged. Install the new foam filter in the housing and then the top and side cases. I did not reinstall the cover of the carb adjust needle screws so I could adjust the fuel/ air mixture to run at peak performance. Hope this helps! The kit that I got was perfect and there are some useful instructions included. Thank you! Respectfully Mark Read more...
Your Price
$9.96
   In Stock
Craftsman Blower Fuel Line Kit
PartSelect Number PS9982433
Manufacturer Part Number 581798001
Fixes these symptoms
Installation Instructions
Richard from SAINT LOUIS, MO
I still have not received the part lost in shipping
I have tried to get a hold of you and the shipper (UPS) and have had no luck I am glad that you have finally sent out a survey or questioner, please help Rick 3142207433 customcontract@ymail.com Read more...
Your Price
$17.26
   In Stock
Craftsman Blower Bag
PartSelect Number PS10009681
Manufacturer Part Number 753-06659
This is a vacuum bag that is used for leaf blowers/vacuums to catch and collect grass suctioned by the blower itself. If you find that the collection bag for your leaf blower is torn, broken or damaged, you will want to replace it immediately to avoid issues with it collecting debris. This bag is made of a durable textile and features a narrow hole to which you can connect it to the leaf blower. Featuring a strap for carrying support, a zipper on the bottom for emptying, and a clamp on the narrow end for a more secure connection to the vacuum, this bag is directly from the original equipment manufacturer and is sold individually. Simply remove the old bag and place the new one on the vacuum end of the leaf blower and clamp it to secure it.
Your Price
$7.46
   In Stock
Craftsman Blower Assembly-Cap W/Ret
PartSelect Number PS11824247
Manufacturer Part Number 578931503
Your Price
$7.50
   In Stock
Craftsman Blower Snowblower impeller
PartSelect Number PS12504101
Manufacturer Part Number 753-08491
Your Price
$63.25
   In Stock
Craftsman Blower Bag
PartSelect Number PS11991241
Manufacturer Part Number 90535411
Your Price
$30.66
   In Stock
Craftsman Blower Starter housing
PartSelect Number PS12496126
Manufacturer Part Number 753-08520
Your Price
$3.99
   In Stock
Craftsman Blower Carriage Bolt, 5/16-18 X .62" Lg.
PartSelect Number PS9088287
Manufacturer Part Number 710-0260A
This genuine OEM carriage bolt is used to secure various parts in lawn and garden outdoor equipment. The bolt has a round head with a square area underneath it that prevents the bolt from turning and coming loose when it is installed. The bolt shaft has a diameter of 5/16 inches, with 18 threads per inch and the threaded portion of the bolt is 0.62 inches long. If the bolt is corroded, the threads are worn down, or the head is damaged or deformed, you will need to replace the bolt to keep your equipment parts secured and functioning efficiently. To replace the bolt, first remove the nut using a wrench or socket. Once the nut is removed, you can unthread the bolt. Insert the new bolt in position, thread the nut on and use a wrench to tighten it. Be careful not to overtighten the bolt to avoid damaging it or stripping the threads. This carriage bolt is sold individually.
Your Price
$4.99
   In Stock
Craftsman Blower Assembly-Knob
★★★★★
★★★★★
1 Review
PartSelect Number PS9285100
Manufacturer Part Number 530059796
Your Price
$11.20
   In Stock
Craftsman Blower Kit - Cruise Control
PartSelect Number PS9028917
Manufacturer Part Number 545081822

Craftsman Blower Appliance Types

Popular Craftsman Blower Models

Below are the most popular Craftsman Blower models we have. Enter your model number in the search box to find your model.