Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
This is the replacement fuel line 25 Inch for several OPE products that use small engines. The fuel line carries fuel from the tank to the carburetor. Over time, the fuel line can become badly clogged, and it can become brittle as well. When the fuel line is badly clogged or cracked, fuel can leak out and it can make it difficult to start or run the engine. To replace the fuel line, carefully disconnect the old line from the carburetor and from the fuel grommet, then replace it with the new line. This fuel line is 25 inches in length and is made of clear plastic. The fuel line is sold individually and is an OEM part sourced directly from the manufacturer.
How Buying OEM Parts Can Save You Time and Money
Why buy the real thing?
OEM stands for Original Equipment Manufacturer. Simply put, this means that the company who made your appliance is also supplying the replacement part for it.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Murphy C - November 7, 2018
Verified Purchase
Perfect fit
Easy purchase and fast delivery. Part fit perfectly.
★★★★★
★★★★★
Tony S - April 13, 2020
Verified Purchase
Great part
The parts went together perfectly. My weed wackier is running at tip top. Thank you
★★★★★
★★★★★
Keith B - August 1, 2024
Verified Purchase
Great part performed as expected
Great part fast shipping
★★★★★
★★★★★
Steven W - June 23, 2018
Verified Purchase
As described
Seems to be of good quality. Time will tell.
★★★★★
★★★★★
PETER S - February 5, 2019
Verified Purchase
Wrong type of fuel line
This fuel line did not fit my machine. Too small. You should specify exactly what machines it will fit.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.0 / 5.0, 8 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Split fuel line driving brother-in-law to frustration
Seven screw, three case cover, two air cleaner, two carb mounting, pulled carb, drained tank, pulled old fuel line, treaded new one in, wire to thread, thread to angle cut fuel line. Reassemble, test, sharpen chain, retest…not exactly a doityourselfer, graduate degree in mechanical/industrial engineering and former medium/heavy mechanica
... Read morel. Get fuel line on carb prior to reassembly, line may need some stretching with a tapered punch.
Read less
Howard from UNICOI, TN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
installing fuel through fuel tank wall
To start, remove the plastic carburetor grill. DO NOT remove the carburetor. The fuel line has to be sliced down to fit through the tank hole and get it in far enough up into the tank to grab with needle nose pliers.( need long needle nose pliers which I didn't have) I placed about six inches of the plastic tubing in the jaws of vice so t
... Read morehat half of the tube was squeezed in the vice jaws. I then used a razor blade to shave off the exposed tube. I slipped the shaved end of the tube up through the tank hole far enough to grab with long tweezers and pulled it up to where I could grab it in the tank with needle nose pliers. I put light lube oil on the remaining tubing and pulled it through. It takes a steady firm pull to pull it in. Install the filter and pull the tube back down into the tank. I also used a small diameter drill bit and with my fingers slightly reamed the tube ends to ease the tube over the filter and carburetor nipples. To prime the engine, spray starting fluid into the carburetor and start. Repeat until the engine will run on fuel. It took me hours to figure this out, but will take less than an hour with this method.
The machine was offered for free on FB marketplace. The person tried a rebuild of the carb, but could not figure out how to connect the fuel line, which feeds from the tank above the carb. I couldn’t either, so I went to a local parts dealer, who could not find a diameter the same size (it’s tiny). I assumed there may have been a fitting
... Read morein the tank, but if so, it was absent. The only parts that were found in the tank: a large filter in a 3/4”piece of larger tubing and this tiny fuel line was inserted into the other end. The resulting arrangement was long enough to reach the hole in the tank.Since the machine looked spectacularly clean, I used these parts to make it run.
1. Using diagonal cutters, I cut a very sharply angled end on the small line.
2. I generously lubricated the new line and the hole in the tank. I then took angled end of the new line and inserted it into the hole. Using a screwing type motion , I slowly worked it into the tank, using generous amounts of lubricant, until the line was far enough into the tank to grab from the fill hole with needle nose pliers. I then pulled and twisted until the line came out of the top of the tank.
3. I cut the angled end square at this point. I then inserted the filter into the larger tubing the cut about an inch longer than the filter Barb.I then lubed the larger line and the smaller line and pulled the line back into the tank from the bottom until the filter laid flat on the bottom of the tank.
4. At this point, I cut the end of the small line so that about an inch protruded from the bottom of the tank. I then re-lubed that line and inserted into a well lubricated length of larger line of sufficient length to reach the inlet on the carb.
About the carb: the donor of the machine had apparently attempted a rebuild. While it was very clean, he assembled it incorrectly. The metering diaphragm was pinched and he left off two of the four screws which held it together. I disassembled it, and using the correct parts assembled in the correct order, (there are parts for multiple applications included in the kit), mounted it back to the machine, and after about six or eight pulls, it roared to life. I did not get into the jets etc, because they seemed to work. This Walbro carb only has one inlet and no purge bulb, and after adjusting the carb it starts on the third pull every time using the choke as it was designed to.
Straight forward, trick for the piston ring was to cut a soda can to make a sleeve that could be wrapped around the piston ring. A bit of duct tape with a tab held it shut until the piston was in position then it was easily removed as the piston was slid in.
Be sure the fuel line is the exact same size (id and od) as the one you are replacing. I had purchased a Fuel line from my local dealer - and after a few hours I figured out that it was the wrong size! He simply cut some line from a spool he had. Didn't bother to look it up! The line from this site was perfect! The id is important because
... Read more the line has to Compress to go through the hole.
Both the Fuel line and the Engine fuel line, where dry rotted.
1) While still attached to the fuel tank, I first sized up the old fuel lines with the newer fuel lines. 2) With a pair of needle nose players, I then removed the old dry rotted fuel ?? lines, from the fuel tank. 3) I cleaned the fuel tank and around the carburetor area, to insure that there was no debris, that could possibly fa
... Read morell into the path of the new fuel lines installation. 4) I then installed the smaller one of the fuel lines, so that it would be out of the way, of the larger fuel line. I Pulled the fuel line through the smaller hole in the fuel tank, with needle nose players. I pulled the smaller fuel line out through the fuel tank filler hole, attached the fuel filter to the smaller fuel line. I Made sure that the fuel filter was extended to the furthest end of the fuel tank bottom. Six inches in all. I then attached the smaller fuel line to the carburetor. 5) I Installed the larger fuel line, followed the same procedures as the smaller fuel line. 6) Both fuel lines where cut on an angle for easy installation. No lubricant was necessary. 7) I filled up the fuel tank with fresh fuel and oil, new air filter and spark plug. It started on the first pull. Amazing.
Replaced all fuel lines. Followed instructions found on Partselect.com, which said to insert cut fuel line in tank and use forceps to reach back in the tank and pull the fuel line through. The problem was that I did not have forceps, or needle nosed pliers that could reach the end of the hose.
Instead of running the line into
... Read morethe tank, I found another suggestion online to run the line from inside the tank outward, allowing me to grab the line with any pliers and thread it. The way I did this was used about a foot length of 14 gauge copper wire. Put an inch or two into the hose (that has been cut on an angle), and use a little black tape to secure the hose on the wire. Now you should be able to route the stiff wire from inside the tank to the fuel hole in the tank. Fish the wire through, and it should be enough to get the tapered end through the tank. Pull the copper wire, mine came out, but there was enough of the hose exposed on the outside of the tank for me to grab with pliers and pull it through.
Removed the top cover (T25 torx), and side cover (T25 torx) with recoil starter. Drained all fuel, and removed all pieces of fuel old fuel line and the weighted filter from inside the tank by shaking out and the (long forceps). A spot headlamp makes it easier to see inside the tank for much of the procedure. Remove the foam filter to find
... Read more the two 8mm nuts and remove the air filter housing and carburetor (nut driver, 8mm socket) the choke lever slides out of its slot with some wiggling and moving the carb back off the mounting studs. Leave the throttle cable attached to the filter housing and move both assemblies out of the way to access the top wall of the fuel tank. There is a cover over the carb adjust screws that wiggles out also. The fuel line and purge line both pass through the wall of the tank and need to be pulled out with some effort (long curved forceps) from inside the tank through the fuel fill port. They are a tight fit. Pay attention to the lines size and location. Large line is in the position away from the recoil starter with the little plastic fitting hanging near the top of the tank. The smaller line is closest to the recoil starter. Both new lines will need to pass through the tank wall (this is the most difficult part). To facilitate the initial entry through the wall of the tank, cut a tapered end on your new lines. Use a very slippery lube to coat the end of the line and push it into the tank as far as you can from the top (forceps or soft grip pliers) help. Look inside the tank and pull the lines through fully out of the tank fill (long curved forceps and head spot light). Don't pull all the way through the fuel fill, just enough to install the new fuel line fitting in the return purge line and the new weighted filter on the fuel line and pull the lines back inside the tank. The return line with fitting close to the top of the tank and the filter hanging so it lays at the bottom of the tank, and able to swing around so it keeps contact with fuel at all times. Remove the old purge/primer bulb two screws (Phillips). The short stem is suction, long stem is pressure. Don't mix them up and connect lines backwards, don't ask me how I know! Lol! If you have such a saw like mine, that has no fuel lines intact, it is difficult to vision the line routes. There are helpful schematics on the internet. Just remember that the purge bulb long fuel stem sends pressure back to the tank through the return line (larger line in the tank with the line fitting away from the recoil). That line can now be cut to length and pushed on the bulb long stem. The suction side of the bulb short stem, connects to the purge line on the side of the carburetor (short line). You need to cut that line to the same length as the old one. It has to curve twice to get to the suction side of the purge bulb without kinking. The only other line left is the fuel line with the filter attached hanging inside the tank. Be sure you have the filter able to lay on the floor of the tank and move around. That line connects to the carburetor opposit side from the purge bulb. Dont cut that one until the carb is installed for proper length. The fuel routes from that filtered line into the carb, then out of the carb to the purge bulb suction side, then out to the return line in the tank with the fitting end. That fitting installed into the line serves only to keep the line from pulling back out of the tank, nothing attaches to it. Make sure all lines are clear of the mounting area of the carb, and throttle function. Pass the bulb lines through the slot in the side of the case being sure the lines don't kink. Secure the bulb with the two phillips screws. Position the carb on the studs and slide the choke lever into its place in the case as you go. Place the filter housing on the studs and push the carb and housing down watching the fuel lines for any kinks, especially where the throttle cable is in close proximity to the short carb purge line. Check the throttle function for interferance, and Install the two 8mm nuts. Now route the fuel line around the throttle mechanism out of the way, hold it to the barb on the side of the carb and cut it to length and install. Put some fuel mix in the tank (dont fill it) to test. Press the primer bulb, tilting the saw with fill cap removed, and see if anything leaks, also watch fuel flow back to the tank inside as you press the bulb. You should see fuel and air bubbles from the purge line. When all air bubbles are gone the system is purged. Install the new foam filter in the housing and then the top and side cases. I did not reinstall the cover of the carb adjust needle screws so I could adjust the fuel/ air mixture to run at peak performance. Hope this helps! The kit that I got was perfect and there are some useful instructions included. Thank you! Respectfully Mark
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
16 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Larry
March 15, 2018
Need the fuel line that will fit through the hole in the bottom of the tank. Outside diameter measures .065 approx.
For model number GTI 19T
Hi Larry,
Thank you for your question. The part number listed under your model number for the fuel line is PS9472280. I hope this helps. Thank you and have a great day!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
September 6, 2021
What is the id & od of fuel line?
For model number Poulan Pro 295
Hi Robert,
Thank you for your question. The inner diameter is approximately 5/64th inches and the outer diameter is approximately 9/64 inches. We hope this helps! If you have any questions, please let us know.
9 people found this helpful.
Was this helpful?
Thank you for voting!
Arnold
March 30, 2023
What size is the gas line in circum..
For model number 1400
Hi Arnold, thank you for your question. The fuel line, part number PS9472280, has a 0.080-inch inner and a 0.14-inch outer diameter. So the inner circumference is approximately 0.25 inches, while the outer circumference is 0.44 inches. We hope this information helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Arthur
December 7, 2023
how far should the fuel purg line be in the tank and can you use the same fuel line for both inlet and purg?
For model number bvm200fe
Hello Arthur, Thank you for writing. The Purge and Fuel lines are different and we suggest replacing them with the proper parts. Here is a link to a How to Video for the Purge Line that may help. Good luck with the repair!
https://www.youtube.com/watch?v=Du9v9hfN1wg
Was this helpful?
Thank you for voting!
James
November 17, 2023
Need primer bulb and fuel line.
For model number 358 350380
Hello James, thank you for your question. The Bulb is 530047721 and the fuel line is 530069247. We hope this helps.
Was this helpful?
Thank you for voting!
Jim
March 15, 2022
I have a Wild Thing 18cc chainsaw and need the purge bulb, the two lines (and possibly a new fuel filter). Do you sell this as a kit. I don't really need 2 ft of each type of line.
For model number P4018WT
Hello Jim, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is Part Number: 530047721 for the Purge Bulb. Part Number: 530069247 and Part Number: 530069216 for the Fuel Lines and Part Number: 530095646 for the Filter. These parts are not sold as a kit sorry, they are only sold separately. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
JIM
April 9, 2022
REPLACCE THE ADDITIONAL LINES IN THE FUEL TANK IE PURGE LINE FROM THE FITTING IN THE TANK AND ARE THE FITTINGS INCLUDED WITH THE LINE OR SEPERATE ORDER?
For model number P3314
Hello Jim, Thank you for your inquiry. We have researched the model number you have provided and show the fuel line as part# 530069247, the purge line as part# 530069216, and the fuel line fitting as part# 530023877. We also have repair videos on installing the fuel line and purge line. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you! https://www.youtube.com/watch?v=UmEwP6rxpLw replacing the fuel return line
https://www.youtube.com/watch?v=Du9v9hfN1wg replacing the purge line
Was this helpful?
Thank you for voting!
John
March 4, 2022
Would this fuel line fit? And if not, do you have one that would?
For model number Poulan 2375 chain saw
Hi John,
Thank you for your question. The part number listed under your model number for the fuel line is 530069247. If you would like to place an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Larry
April 23, 2022
How to replace fuel line
For model number 358.356241
Hi Larry,
Thank you for your question. Here is a link to one of our YouTube videos that you may reference on how to install the fuel line, https://www.youtube.com/watch?v=UmEwP6rxpLw. The chainsaw in the video may appear different from yours, but it will give you a general idea on how to install the part. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Larry
March 27, 2022
Need gas line diagram
For model number S1634
Hello Larry, thank you for writing. We do not have the any diagram for you model. We do have the Fuel Line 530069247( and a similar video) as well as the Purge Line 530069216. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS9008183
Manufacturer Part Number: 530069247
Item is in stock and is estimated to be delivered in 2-3 business days via Standard Shipping.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Trimmer","title":"Trimmer","url":"/Trimmer-Parts.htm"},{"position":2,"name":"Hose or Tube","title":"Hose or Tube","url":"/Trimmer-Hoses-and-Tubes.htm"},{"position":3,"name":"530069247","title":"530069247","url":""}]
You added 1 item to your cart
✖
% OFF
$
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
