Saw Seals and Gaskets

Saw O-ring This is an authentic manufacturer sourced replacement part designed for use with Dewalt grinders. It helps to provide an air tight seal for the gearbox. It is made out of rubber material and it is sold individually. To complete this repair you will need a spanner wrench.

Saw Rubber Gasket

Saw Gasket This genuine manufacturer-sourced part is specially designed for use with Skil and Bosch saws. The purpose of this gasket is to provide a tight seal for the housing, unfortunately, over time it will wear out and it may begin to crack eventually requiring a replacement. Keep in mind this high-quality component is made of durable composite material and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware.

Saw O-ring 5 O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

Saw Felt Seal It is an authentic item that is supplied directly from the original equipment manufacturer for use with Milwaukee saws. This special seal helps to provide a tight fit between connected components. It is an identical replacement for a missing or a worn part that was installed on a new unit. Please make sure to refer to the appropriate diagram of your model for the exact location and application of this part. Keep in mind this high-quality seal is made of durable felt material and is sold individually.

Saw Seal Ring It is a genuine replacement part that is supplied directly from the original equipment manufacturer for use with Makita reciprocating saws. This is the special component which is used to provide an air-tight seal for the gear housing assembly, over time the material tends to deteriorate and may crack eventually requiring replacement. It is a high-quality part which is made of durable rubber and it is sold individually.

Saw Gasket

Saw O-ring 35 O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression</u> O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

Saw O-ring Hub This is available as an individual replacement part. The o-ring hub is made of rubber and goes between the hub and gear. A screwdriver, a set of pliers, and a wrench set may be needed during the replacement of this part. It may become broken and will need to be replaced. This item is an original part from Milwaukee for use in saws.

Saw Seal This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sold individually. Replacing this item you would need a wrench to replace this item.