Poulan Pole Saw Carburetors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Poulan Pole Saw Carburetors
Your Price
$12.20
In Stock
Poulan Pole Saw Purge Bulb
Instead of running the line into the tank, I found another suggestion online to run the line from inside the tank outward, allowing me to grab the line with any pliers and thread it. The way I did this was used about a foot length of 14 gauge copper wire. Put an inch or two into the hose (that has been cut on an angle), and use a little black tape to secure the hose on the wire. Now you should be able to route the stiff wire from inside the tank to the fuel hole in the tank. Fish the wire through, and it should be enough to get the tapered end through the tank. Pull the copper wire, mine came out, but there was enough of the hose exposed on the outside of the tank for me to grab with pliers and pull it through. Read more...
PartSelect Number PS9003852
Manufacturer Part Number 530047721
This primer bulb, also known as a purge bulb, is used to push more fuel from the fuel tank into the carburetor of your small engine equipment, to help the engine start easier. Over time and through extended use and exposure to gas and oil, the bulb of the primer will eventually lose its elasticity and crack or break. This bulb is made of plastic and can be replaced by accessing the ignition system. Disconnect the fuel lines and pop out the bulb with a set of pliers, and once you pop in the new bulb, you just reconnect the fuel lines. This bulb is compatible with a variety of makes and models of small engine equipment and is sold as an individual part.
Installation Instructions
Robert from MANVILLE, NJ
Replace the fuel lines
Replaced all fuel lines. Followed instructions found on Partselect.com, which said to insert cut fuel line in tank and use forceps to reach back in the tank and pull the fuel line through. The problem was that I did not have forceps, or needle nosed pliers that could reach the end of the hose. Instead of running the line into the tank, I found another suggestion online to run the line from inside the tank outward, allowing me to grab the line with any pliers and thread it. The way I did this was used about a foot length of 14 gauge copper wire. Put an inch or two into the hose (that has been cut on an angle), and use a little black tape to secure the hose on the wire. Now you should be able to route the stiff wire from inside the tank to the fuel hole in the tank. Fish the wire through, and it should be enough to get the tapered end through the tank. Pull the copper wire, mine came out, but there was enough of the hose exposed on the outside of the tank for me to grab with pliers and pull it through. Read more...
Your Price
$57.37
In Stock
Poulan Pole Saw Carburetor
PartSelect Number PS16352852
Manufacturer Part Number 530071811
This is a genuine OEM replacement part, it is sold individually. It is used on specific Gas Trimmers. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem.
Your Price
$11.75
In Stock
Poulan Pole Saw Insulator
PartSelect Number PS12604475
Manufacturer Part Number 530057547
This part is available as an individual replacement part. The carburetor adapter attaches to the gasket. During replacement, it may require an allen wrench to help install this part correctly. It is made of plastic and will require replacing if it breaks. This genuine item is supplied by the original equipment manufacturer for use with Poulan and Weed Eater trimmers.
Your Price
$23.86
In Stock
Poulan Pole Saw Carburetor
PartSelect Number PS16365356
Manufacturer Part Number 545006017
This genuine OEM sourced replacement carburetor is specially designed for use with Craftsman handheld trimmers. The purpose of this part is to mix the air and the gas before the combustible mix goes to the engine. If the engine won't start and the tank is full of fresh fuel or if the engine starts and then quickly dies, the carburetor is likely the problem. This high-quality component has a durable metal body and it is sold individually.
Your Price
$5.50
Special Order
Poulan Pole Saw Choke Lever
PartSelect Number PS12636913
Manufacturer Part Number 530071717
This is an authentic replacement part that has been sourced from the original manufacturer to be used with trimmers and pruners from Poulan and Weed Eater. The choke lever includes the valve plate and is used to restrict the flow of air sending a richer fuel/air mixture to the combustion chamber when cold starting the engine. This item is available as an individual replacement part.