Agitator Shaft O-Ring WP22002417 | Official Whirlpool Part | Fast Shipping | PartSelect
Agitator Shaft O-Ring – Part Number: WP22002417
( Grid squares measure 1x1 inch )
Agitator Shaft O-Ring – Part Number: WP22002417 https://partselectcom.azureedge.net/Schematics/Maytag/50465.gif

Agitator Shaft O-Ring

PartSelect Number PS11739362

Manufacturer Part Number WP22002417

Manufactured by Whirlpool

Product Description

Agitator Shaft O-Ring Specifications

Also known as Rubber Seal.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Leaking

This part works with the following products:

Washer, Washer Dryer Combo.

This part works with the following brands:

Maytag.

Part # WP22002417 replaces these:

22001813, 22002417.
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Customer Repair Stories
Average Repair Rating: 2.6 / 5.0, 4 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dan from Mason, OH
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench set
Parts Used:
6-2095720, 6-2040130, WPY015667, WPY015666, WP22002417
Washer Leaking and Spin Cycle stopping frequenly
* Remove front Panel
* Remeove two screws that allow the top to hing up.
* Loosen set screw on agitator (1/4" socket)
* Remove Agitator
*Loosen spanner nut from mounting seal with hammer and punch remember to loosen, turn clockwise
* Remove Inner Tub
* Losen Mounting stem with Hammer and Punch- Remember to loosen, turn clockwise
* Remove Boot seal with hands
* Remove bolts from the three brackets that attach to the outer tub
* Remove Outer Tub hoses
* Remove outer Tub. CAREFUL, I cut my hands on sheet metal when outer tub broke free and came up
* Knock Outer tub bearing out with large block of wood
* Cut bearing sleeve off of the transmission with a drimmel tool and cutting wheel. It was siezed on and would not turn off. Also, first tried to chisel , but was too difficult
* Cleaned area where bearing sleeve came off with fine sandpaper
* Put small amount of non-permanent thread lock on transmission (bearing area) before installing the new bearing sleeve because the sleeve is not pressed on and I did not want it to turn freely
* I did not but new bolts for the outer tub 3 brackets, but noticed that they needed to be sealed. So I bought some rubber washers at hardware store
* I also used some stuff called CLR to clean some rust off of the outside of the INNER tank
* I replaced the O-ring on the top of the agitator shaft
Also, on the agitator shaft: To really do it right, I probably should have changed the agitator shaft because the old seal wore grooves into the shaft. I took my chances and cleaned it up with some fine metal sandpaper. I could not get the worn grooves completely smooth, but did not want to take off more material as I thought it may cause a leak. We'll see
* I just used a hammer and punch to retighten the mounting stem and Spanner nut. REMEMBER COUNTER CLOCKWISE TO TIGHTEN
* This was not too bad if you are somewhat mechanically inclined. I could have got a new washer, but quite frankly, I get more satisfaction from seeing the old one keep working
* One last thing...and this is mostly for the younger guys cause the older guys already know it. CLEAN EVERYTHING on the washer...make it look like NEW and tell your wife how much you saved. Make sure you have the parts and tools to do the job within a timeframe that you do not have to go to the laundry mat and do not leave a big mess. This advice will definately pay off.
GOOD LUCK
196 of 206 people found this instruction helpful.
Was this instruction helpful to you?
Beverly from Manchester, TN
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
Parts Used:
6-2095720, WP22002417, WP6-2168983, WP22002340
shaft lock was damaged and agitator would not stay down in proper location
Made a 4 prong wrench from a 2" pipe coupling to remove retaining nut. Had to tap retaining washer a few times with hammer and after that it came off very easy. All other work was very easy. parts went together with ease. Saved company several $'s as we were told it was not recomended to repair and should replace washer. Under $100 for parts and a couple hours labor.
44 of 57 people found this instruction helpful.
Was this instruction helpful to you?
Johnny from Cedarburg, WI
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench set
Parts Used:
6-2095720, WPY015667, WP22002417, WP22002340
Agitator shaft and agitator came up and leaked water
lifted washer top, removed front panel, took punch and hammer to loosen collar (right to loosen- left to tighten) removed tub replaced seals and o-ring. then replaced the nylon retaining ring then reassembled. all works well now no leaks. Easy fix saved $500.00
18 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Tim from Diamond, MO
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Parts Used:
6-2040130, WPY015667, WPY015666, WP22002417
Leaking water from bottom
I followed Dan from Mason OHIO instructions.They were perfect. I have a different series washer so I did not need the washer and retaining ring. I used 2 lengths of 4x4 to support the tub when smacking the bearing with the narrow side of a 2x4 to drive it out. You hit it from the inside of the tub. When installing the new one, use the wide side of the 2x4 to drive it flush.
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Model Cross Reference

This part works with the following models:

PartSelect Number: PS11739362
Manufacturer Part Number: WP22002417
Brand
Model Number
Description
Maytag
LAT1916AAE
Washer - Residential
Maytag
LAT1916ABE
Washer - Residential
Maytag
LAT2200AAE
Washer - Residential
Maytag
LAT2300AAE
Washer - Residential
Maytag
LAT2300AWW
Washer - Residential
Maytag
LAT2301AAE
Washer - Residential
Maytag
LAT2500AAE
Washer - Residential
Maytag
LAT2600AAE
Washer - Residential
Maytag
LAT2916AAE
Washer - Residential
Maytag
LAT2916AAM
Washer - Residential
Maytag
LAT2916ABE
Washer - Residential
Maytag
LAT3500AAE
Washer - Residential
Maytag
LAT3500AAQ
Washer - Residential
Maytag
LAT3600AAE
Washer - Residential
Maytag
LAT3600AAQ
Washer - Residential
Maytag
LAT4916AAE
Washer - Residential
Maytag
LAT4916AAM
Washer - Residential
Maytag
LAT4916ABE
Washer - Residential
Maytag
LAT5006AAE
Washer - Residential
Maytag
LAT5006AGE
Washer - Residential
Maytag
LAT5006GGE
Washer - Residential
Maytag
LAT5916AAE
Washer - Residential
Maytag
LAT5916AAM
Washer - Residential
Maytag
LAT5916ABE
Washer - Residential
Maytag
LAT7306AAE
Washer - Residential
Maytag
LAT8006AAE
Washer - Residential
Maytag
LAT8006AAM
Washer - Residential
Maytag
LAT8016AAE
Washer - Residential
Maytag
LAT8026AAE
Washer - Residential
Maytag
LAT8026AAM
Washer - Residential