Plastic Motor Pulley WP21001108

First unplug the washer machine..then lean it back to get room to the motor pulley I didn't have to remove the motor just tap the pulley with a rubber hammer until it was released I did put a little of dish detergent for easier removal an did the same to install the new pulley then slightly tap in with rubber hamer ..

The washer was making a terrible squealing noise and when I examined it, I found the drain pump was leaking. I found a few videos online and then found this site when I started searching for replacement parts. I was originally just going to order the drain pump, but this site lead me to check out the underside of the washer where I foun ... Read more d the belt had basically melted onto the motor wheel. Watched a few videos here, determined that the motor itself was still operating fine, so i ordered a drain pump, motor wheel, and a new belt. 2 days later they arrived. The motor wheel was hard to get off. I ended up prying it off with a hammer. Then gently tapped the new one on. Replacing the drain pump was simple - use a socket wrench to unscrew the 3 bolts holding it on, disconnect the hoses, then just do the reverse to put it back. At that point, I just slipped the new belt on, made sure everything was turning smoothly and ran a small test load in the washer. It was as good as new and cost me a lot less than buying a new one or calling a repairman.

I just put the pully on then put the belt on and started washing clothes thank you very much for your help in getting me the pully in a timely matter aloha

Used piliers and screwdriver to remove old pulley.When putting on the belt make sure you have it tight enough.I had to buy a new pulley and do it over.

The drain pump assembly was going bad. It eventually froze and burned the drive belt and motor pulley up. I replaced the drain pump by removing 3 screws. I replace the motor pulley and belt in about 5 minutes without removing any parts. Simple fix. Ran through 3 cycles and works perfectly. Thanks!

I used a small screw driver to remove the teeth from the motor pully and fit the puller on the pulley with a small socket protecting the end of the shaft. it came off easily with a few turns on the puller. I placed the new motor pulley on the shaft and tapped it into place with a small dead-blow mallet (a hammer with a hollow, heavy, plas ... Read more tic head filled with sand). Unfortunately, the spin /transmission shaft pulley was an incorrect part for the application and the motor turned out to have some internal heat damage. I was not able to apply this part because it was the wrong application but if it is you are in luck. The clip removal is the same and install this pulley flat side down and reassemble. If not, read on. I removed the motor by removing the front panel, removing the three bolts securing the motor to the plate, and disconnecting the wiring plugs and ground wire. I lucked out finding a spin pulley and motor rebuild kit locally. After rebuilding the motor with the new bushings, brushes, etc. from the kit, I reinstalled it by reversing the removal steps. I then removed the spin/trans pulley by removing a plastic grease cup/cover from the end shaft and removed the C-clip and washer holding the pulley in place with a small screw driver. I was careful not to let the pulley and washer/thrust washer stack on top of it fall off so I could be sure of the order in which they should be reinstalled. I applied fresh grease and reversed the disassembly proceedure making sure to drive the C-clip fully into the slot on the shaft with a large flat-tip screwdriver and the mallet. I cleaned, regreased, and reinstalled the grease cup/cover back into place firmly making sure it snapped into place. I slipped the belt back on the pulleys and reinstalled the front panel with the two screws at the top inside corners. The job was done.

repaced faulty pump,motor pully then installed a new belt

Just tipped it back pulled the pulley off (the little plastic tits on the shaft just break off) the belt comes off easy. Carefully tap the new pulley on using a little grease or petroleum jelly on the splines before hand. The belt goes on easily when you slide the motor over. Just force the belt onto the big pulley just as you would on yo ... Read more ur car.
Problem was... the new belt and pulley burnt right up again when it tried to agitate after filling. So the motor was turning fine, and the pump shaft was turning fine, but the agitator (tranny) must have been locked up. Its pulley (the big one) would spin in one direction but was locked in the other when I checked it. Not knowing any better, I assumed that was normal. I still don't know if it is or not. That's the problem with these chat sessions...One guy says it should spin freely both ways another says it should be somewhat difficult to spin, you don't know if the control has to be set in a certain spot before checking. I gave up just going to buy another. This time a direct drive, although it doesn't make any difference there all junk.

took hammer,screwdriver,cut old one off then took the newone and aline it up on spline put socket over it drove it on.a little at a time untell the lock on the end whent in the groove. done thank you. ps you dont have to buy a motor with pully.

loved that I was able to get just the part i needed and not the whole shaft