Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle.
This part is black, made of metal, and around an inch in length. It i...
This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending...
This ground drive fixed idler pulley is for lawn tractors.
910 inch offset
Ground drive fixed idler pulley helps apply tension to the drive belt, allowing the belt to turn.
Wear work gloves to...
This flat idler pulley is a genuine OEM replacement part for use in outdoor power equipment. It is made of plastic and features a metal bore adapter, and a radial-style single row bearing. The pulley ...
This ignition switch is an OEM replacement part found near the steering wheel or dashboard in lawn tractors and riding mowers. The switch has four symbols on the top side which indicate its various fu...
This OEM hardened washer spreads load under the bolts of your lawn tractor. It is silver, made of metal, and is sold individually. Over time, the washer may become damaged due to wear and fatigue, and...
This parking handle is an original part from Craftsman for lawn tractors and riding mowers. This part connects to the brake rod for putting on the parking brake. It is recommended to review your model...
E Ring Number 5133-75 is a black, metal ring for securing the position of other parts. If damaged it will become loose or fall off. Installation is rated as "Easy" and is done with a pair of pliers. R...
This OEM-certified washer provides support, spacing, and reduces friction between parts in your lawn equipment, typically working alongside bolts or screws. This washer has a thickness of 16 gauge and...
Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carr...
This metal square key is designed to prevent the rear wheel of your lawn equipment from slipping. Approximately sized at 3/16 x 2, it fits into the groove found on the axle and the hub of the wheel, e...
This Husqvarna Steering Shaft Assembly is a robust and integral component for your lawn tractor. With a length of 29-1/4 inches, this assembly works efficiently to link the steering wheel with the sec...
$59.15
In Stock
Order now and your part arrives by May 7
Questions And Answers for YTH21K46
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
The drive belt literally goes from the back of the tractor to the front. The mower must be removed, helps to have the tractor up on blocks to give adequate room for work on underside. Belt goes easiest on the engine first, then thread to the rear, install on the rear, (driven pulley) then on the idlers. Check to assure that it function
... Read mores properly before re-installing the mower. If you have the owners manual, there is a diagram, (check your orientation, it is not clear if it is a birdseye or under tractor view) which offered some help. When replacing belt, check the transaxle front mount, mine was broken which is why the belt came off in the first place. Repairing the mount was quite a job in itself, but now works fine.
ALL VIDEOS and the official Husqvarna instructions will tell you that you MUST remove both the mowing deck and the entire clutch pulley assembly to switch the transmission drive belt. This is NOT true. It takes some effort and tight maneuvering, but this job can be done relatively quickly without removing either. You do NOT have to rem
... Read moreove the mowing deck! You do NOT have to remove the clutch pulley assembly! What I did was to stand the tractor up nearly vertical, resting it against a golf cart I have and tying it in place for safety. Then, you have to loosen two black belt guides right by the clutch pulley assembly. I did NOT remove them, just left them hanging loose. Next, there is a silver bar that comes in from the outside of the mower chassis and attaches directly to the clutch, remove this entirely. Next, there is an electrical cord assembly in the way, trace this back, find where it plugs in, and unplug it. Next, in order to be able to slide the belt fully over the clutch pulley assembly, you have to take the mower deck belt off of JUST THE ONE spindle closest. I tie wrapped it in place after getting it off the spindle so that I could easily put it back onto the spindle as the last step when done. Once the mowing deck belt is off the closest spindle, you can then slide the drive belt completely over the clutch pulley assembly. You can then easily remove the entire drive belt, taking note (I took pictures) of how it is routed. Then, just reverse all of this. I began by fitting the drive belt over the clutch pulley assembly to make sure that end was correct. I then put the previously mentioned two guides, silver bar, and electrical cord back in place. Next, I shoved the belt down where it goes, working it down towards the transmission and routing it correctly. Of course, it is a little difficult with the limited space available, but I would rather do that then needlessly take the entire mowing deck off. You finally have to CAREFULLY slide it over the PLASTIC fan blades on the transmission. Once past those, it slides easily in place. The last step is to put the mowing deck belt that you previously removed and tie wrapped in place back onto the spindle. That's it! Only takes about 30-45 min. done this way.
