Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The heating element (Flat Can Heating Element 5400W, Heating Element, Whirlpool Dryer Heating Element, Dryer Heating Element) provides heat to the dryer. It is metal and measures 10.5 inches long, 7.5...
This dryer door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open, and operates the drum light. White in color and 6.5 inches long, this OEM swit...
The thermal cut-off (Dryer Thermal Cut-Off Fuse Kit, Dryer Thermal Cut-Off Kit) prevents the dryer from overheating when the dryer high limit thermostat fails in a closed circuit condition. This part ...
This Whirlpool Dryer Repair Kit is a convenient solution for fixing noise and drum movement problems in 27-inch dryers. Compatible with models from Whirlpool, Kenmore, Maytag, and more, the kit includ...
A dryer high-limit thermostat (High Limit Thermostat, Hi-Limit Thermostat, Dryer High-Limit Thermostat) is a switch that is actuated by temperature change. This high limit thermostat acts as a safety ...
This white OEM dryer door handle is used to open and close the dryer's door. Comprised of plastic and 6-by-2-inches in dimension, the handle is sold individually and attaches to the dryer door. Your d...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so...
This OEM drive motor is designed to operate the drum in electric and gas dryers by turning the drive belt, enabling proper rotation during drying cycles. Compatible with most Whirlpool-incorporated dr...
This is a genuine OEM replacement rear drum seal for your dryer. This seal is made of felt and comes with the adhesive required for installation. The purpose of the seal is to prevent hot air from esc...
$42.12
In Stock
Order now and your part arrives by Jul 30
Questions And Answers for YMEDX6STBW1
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Yvan
February 27, 2023
Hello, the control of my dryer always remains in the same position no matter what cycle it is placed on and does not stop. Is control the problem? Waiting for a response.Thank you!Have a good Day!
For model number YMEDX6STBW1
Hi Yvan, thank you for getting in touch. According to our research, you may need to check the following parts to fix the issue: timer, part number PS12070926, and Cycling Thermostat, part number PS11745959. We hope this sorts out your problem!
Hi Stephen, thank you for the question. We have found the instructions to access the top console. These may not be of the exact model but will help you to access the top console. You may need to follow these steps:
1. Remove the knobs.
2. Remove the screws across the rear access panel using the screwdriver.
3. Disconnect the switches from the wire harness and remove them.
4. Remember the orientation of the wires.
5. Lift the old console and replace it with a new one.
We hope this information helps!
1 person found this helpful.
Did this question help you?
Thank you for voting!
Taylor
December 1, 2023
The dryer won't start. The light doesn't turn on when I open the door.
What i've checked
Start button has continuity
Power is coming into the dryer (opened the panel at the back and checked with mutlimeter)
I was getting continuity on the door switch (the two prongs at either end when the door was closed, middle and outside prongs weren't getting continuity). I thought that might have been the problem so I replaced the switch, but still no change. No light when I open the door, doesn't start.
I'm really at a loss for what else to check. Any help would be appreciated.
For model number YMEDX6STBW1
Hi Taylor,
Thank you for your question. If you have checked these parts and the dryer still does not start, we would recommend checking the motor. We hope this helps!
Hello Taylor, thank you for reaching out. We would recommend checking the thermal fuse, part number PS11741460, to fix the issue. We hope this solves your problem!
Hello Joanne, thank you for contacting us. The leveling leg you are looking for is part number PS1609293. It is sold individually. If you need help placing an order, customer service is open 7 days a week!
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.
To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.
You can check the heating element wi
... Read moreth an ohm-meter or visually inspect it to see if the heating element spiral wire is broken.
Don't hurry to dispose the old element. My model includes a small electric safety part. You'll need to transfer it to the new heating element (that comes without it)..
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back
... Read more off.
