Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stop...
This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a w...
This is a pulsator assembly, also known as an agitator, for your washing machine. This pulsator sits at the bottom of your washer and is what is used as the main driving force to wash your clothes. Th...
This drain pump assembly is a genuine replacement part designed for select LG and Kenmore washing machines. It plays a critical role in removing water from the washer tub during the drain cycle, ensur...
This is a drain hose assembly for top-load models of LG washing machines. This hose specifically is used to allow water to drain from the tub to the drain pump of the washer. This hose is made of plas...
This clutch housing assembly with mode shifter, or washer drive shaft and shifter assembly, is made for your washer. It connects the appliance wash plate to the motor so the washer can shift the drive...
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pum...
Introducing the customized screw designed exclusively for LG washers. Manufactured with safety and efficiency in mind, installation is straightforward when you adhere to correct safety regulations. Sh...
This water-level pressure switch in your wash monitors and regulates the water levels throughout the fill, wash, and rinse cycles. You will usually find it inside the control panel or near the tub. It...
This part is the replacement fabric softener cap for your washer. It is also known as the washer dispenser drawer insert. It is made of blue plastic and is approximately 4 1/4 inches by 2 1/4 inches. ...
This part is the replacement switch assembly for your top-load washer. It contains the switch mechanism and the connecting wire that hooks the door latch to the electrical system of the washer. The li...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
L
April 14, 2023
When turning the cycle selector knob, it doesn't work with every click of the knob. I have had to spin the knob around several complete turns to get it to move to Perm Press. Sometimes it moves to the next one after 5 or six clicks, sometimes not. I've had this issue for a while but finally got around to trying to replace the knob. Yes I replaced the knob somehow hoping it would work. It didn't. Please help. It's driving me nuts. I feel like I'm spinning a roulette table when I go to wash clothes.
For model number WT7600HWA
Hi, thank you for contacting us. Based on the description, you may need to check the user interface, part number PS11761313, to fix the issue. Before replacing the user interface, you may need to check whether the electronic control board is connected properly or not. We hope this solves your problem!
Washer is filling slowly/incomplete and making load humming noise at times. Water hoses and water have been checked. Filters are clean. What is the next step to correct?
For model number WT7600HWA
Hi Katy, thank you for reaching out to PartSelect. Based on the description that you have provided, we would recommend checking the water inlet valve assembly, part number PS3527446, as it is the most likely cause of this issue. If it is faulty, you may need to replace it. You will need to use a multimeter to verify which part is causing the issue. We hope this solves your problem!
Can the lid be replaced on the washing machine? My husband scratche our lid while moving and ruined the chrome on top
For model number WT7600HWA
Hello, Thank you for your question. Looking at your model number there are no parts available listed under that section, so there is a chance the parts could be no longer available. There are no part substitutions listed. My suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers. We hope this helps.
Did this question help you?
Thank you for voting!
Rodney
June 19, 2022
water softener holds water after wash
For model number WT7600HWA
Hello Rodney, Thank you for your inquiry. Check for any blockages in the hoses leading to dispenser assembly and the water valve connector assembly, and thoroughly clean the dispenser with a cleaning brush to loosen any debris or residue that might have been left. If that does not fix the issue, you may need to replace the dispenser assembly, the water inlet valve, or the valve to dispenser inlet hose, or the dispenser drain hose. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su
... Read morepplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
I diagnosed by running a full wash. I watched it and when the water should have stopped it kept running. I unplugged the washer from the power and the water kept running. This told me the inlet valve was the issue and not an electronic issue. I stopped the water by closing the water valve manually. Replacing the inlet valve was very easy
... Read more. Hardest part is moving the washer out of the laundry room. The videos online show very simple steps. Maybe 8 screws to remove and a couple of hoses and five electronic connectors. Take a photo of connectors before removing them to ensure you reconnect properly.
