WMH78019HB05 Whirlpool Microwave - Instructions

The nightmare was that this microwave is installed under the cabinet....in order to get to the light bulb I had to pull out my stove then squeeze into the space between the stove and counter....my old microwave light bult was much easier to change.....Shame on Whirlpool for making this so difficult.....must be a better way to cover the light bulb so that we do not need a screwdriver to remove the door to get to the light bulb

Removed 1 screw, removed "burnt out" bulb and replaced it with new bulb.

removed two screws,lowered the glass shield,removed the burned out bulb and replaced it with the new one. I ordered the bulb from parts select and recieved it two days later. It was a pleasure to deal with them, and certainly use them again.

I had some difficulty removing the glass plate because of the awkward (upside down) position of the screw that retained it. After replacing the burned out bulbs and replacig the glass plate the problem of replacing the screw involved my dropping the thing several times before I got the screw threads to catch. I got a screw thread to catch enough to hold the glass plate in position and left it at that.

Read some instructions and easily found the fuse. Replaced it. Still didn't work. Took control panel off to check door switches. Nothing I read mentioned a second fuse. Tested and it to had blown. Ordered another one. Popped them in. Done.

Remove two screws from Vent Grille, one on either side, and remove one screw inside Vent Grille on right side. Pull Vent Grille off exposing the two Charcoal filters. Remove the two Charcoal filters by hand and replace with new ones. Reinstall the Vent Grille and tighten screws. That's it. I'm not handy (ask my wife) and if I can do it so can you.

The original bulb came apart while unscrewing it from the back of the microwave, leaving the metal screw thread contact still in the socket. Since this is an over-the-range micriwave there isn't enough room to manuever needle nose pliers into the socket to remove the screw thread contact. So this is how we were able to remove it.
Unplug power cord.
Take a standard wine bottle cork and whittle down one end until it fits in the socket. Then, using a bit of pressure push the cork into the socket snd begin unscrewing the screw thread contact until it comes out of the socket. Works like a charm!

The hard part was trying to find the light bulb locally. The locally sold light bulbs were either too long, not dual element or not powerful enough. So I ordered the light bulb straight from PartSelect. When it came time to install the new light bulb I carefully removed the screw holding the plate in position so as not to loose it in my gas stove. I needed the mirror to line up the light bulb and screw it in. Once it was in I verified operation and closed up the plate being careful not to drop the screw into my gas stove. Problem solved.

Whirlpool Microwave was purchased as used item, so installation in a new location required purchase of mounting template, wall bracket, mounting hardware. Granite backsplash cut out using wet/dry diamond blade and Ryobi 6.5 inch saw. Microwave exhaust fan removed and rotated for upward exhaust using modified exhaust plenum from existing stove exhaust hood. Installation of Microwave was the simplest part of the job. All mounting materials worked as required. A list of the materials provided in the hardware mount kit would be helpful, I would not have had to order the top mount screws separately if it was clear that they were included in the kit. Otherwise, no complaints.

Replaced bulb by: 1 pulling plug on microwave to make sure not hot - no power; 2 used needle nose pliers with head part about same size that fit inside of socket; 3 opened pliers and held firm against broken metal part; keeping pressure of pliers against broken metal part of light bulb, slowly unscrewed the broken part from socket using firmly held opened pliers. The rest was a cinch...just screwed in new light bulb, plugged in microwave and viola - there was light once again.

I unscrewed the bottom plate of microwave oven and took a picture of how the wiring was plugged in and unscrew the motor and put the new one in,it was so easy to do

Followed instruction already on your website

It was a bit awkward because the microwave is mounted over my stove. I had to twist around and install the bulb and then replace the cover. It was a bit uncomfortable. It took me about 10 minutes to complete.

Put s pot under were you take the screw out.If you drop it you can get it easy

RATHER EASY. PHILIPS SCREWDRIVER, TORX DRIVER (FOR THE 2 SCREWS SECURING THE GEARMOTOR ITSELF), VERY SMALL SCREWDRIVER TO ASSIST IN DEPRESSING THE DETENTS ON ELECTRICAL CONNECTORS AT THE MOTOR. IF THE MICROWAVE IS ABOVE A STOVE UNIT, IT'S A GOOD IDEA TO PLACE A TOWEL DOWN ON THE STOVETOP TO CATCH ANY WAYWARD SCREW IF ONE HAPPENS TO GET AWAY. (VOICE OF EXPERIENCE)