WM1455HWA LG Washer - Overview
Models starting with WM1455HWA
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Rear Tub Gasket
PartSelect #: PS3522855
Manufacturer #: 4036ER2004A
If you notice your washing machine is leaking water from the top of the transmission, it might be due to the gasket being damaged or worn down. When replacing your gasket, consider replacing your tub ...
$24.67
In Stock
Washer Tub Bearing, Rear
PartSelect #: PS11705912
Manufacturer #: 4280EN4001F
Upgrade your LG washing machine with this genuine OEM tub bearing. Designed specifically for LG rear tub models, this high-quality component provides support to the spin basket shaft at the tub, ensur...
$72.00
Special Order
Ball Bearing
PartSelect #: PS7785069
Manufacturer #: 4280EN4001C
The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, th...
$72.00
In Stock
LOCKER,HOOK
PartSelect #: PS8752721
Manufacturer #: MFG63099101
This hook locker, commonly referred to as a door lock strike is specially designed for LG washers. It is a small, metal plate that is attached to the washer door. When the door is closed it engages wi...
$36.85
In Stock
Washer Switch Assembly
PartSelect #: PS7792232
Manufacturer #: EBF61315802
This is a door lock switch, compatible with various models of LG washing machines. This door lock switch is designed to communicate to the control board when the door of the washer is closed, so the d...
$130.68
In Stock
Washer Hose Connector
PartSelect #: PS3527289
Manufacturer #: 5214FR4006G
This part is the replacement connector hose or clean-out drain hose for your washer. It is black in color and is sold individually. The connector hose drains water out of the washer if the drain cycle...
$15.00
In Stock
CAP,DRAIN HOSE
PartSelect #: PS3635866
Manufacturer #: 5006EN3015A
This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before be...
$11.77
In Stock
HINGE
PartSelect #: PS7321743
Manufacturer #: 4774EN3002A
This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in color, and made ent...
$18.22
In Stock
Shock Absorber
PartSelect #: PS3583320
Manufacturer #: 4901ER2003A
This is a replacement shock absorber for your washer. The shock absorber is approximately 10 inches long and a little more than one inch wide. It is black and silver in color, and is sold individually...
$34.74
In Stock
Drain Hose
PartSelect #: PS3527285
Manufacturer #: 5214FR3188G
This drain hose is a genuine OEM replacement part that is specially made for LG washing machines. It is a flexible rubber pipe designed to remove wastewater from the washer. When the washing machine g...
$41.07
In Stock
Common Symptoms of models starting with WM1455HWA
[Viewing 9 of 9]Leaking
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Noisy and Marks Left on Clothes
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer did not recognize the door was shut
I removed the Wire and spring from the tub seal and then removed the seal on the side of the washer that contains the Door switch. I removed the two screws that held the door switch in place while holding the switch with my other hand. Once the screws where out I pulled the switch assembly out thru the gap and removed the wires from old
... Read more
assembly. I then plugged the wires into the new assembly aligned the holes up and put the screws back in the new door switch assembly. I then put the door seal and tub seal holder back on. This took about 15 minutes. I do recomend that you unplug the washer before starting this process.
Read less
Parts Used:
-
CURTIS from OLIVE BRANCH, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer tub shakes violently during spin cycle.
turn washer on it's side. dampers are visible from underneath. use needle nose pliers to "pinch" end of retaining pin and pull pin out. it will take some force to remove. i would recommend replacing all 3 as i had one that had a mounting tab broken off. i then realized the other dampers were bad. there should be resistance in the up and d
... Read more
own motion. if not replace.
Read less
Parts Used:
-
charlie from LAUDERHILL, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drain hose was full of cracks
Slide out double stack unit, take the back off, stand on my head and reach in to remove hose clamo off pump hose. slide new hose on and clamp, but back on, and slide washer/dryer stack back in to place.
Parts Used:
-
Dennis from Sauk City, WI
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
5 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!