Models > WLW1

WLW1 Washer - Overview

Models starting with WLW1

Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
D-Shaped Knob Clip – Part Number: WH01X10106
D-Shaped Knob Clip
★★★★★
★★★★★
(28)
PartSelect #: PS268493
Manufacturer #: WH01X10106
This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the ti...
  No Longer Available
Drive V-Belt – Part Number: 134511600
Drive V-Belt
★★★★★
★★★★★
(28)
PartSelect #: PS1146950
Manufacturer #: 134511600
This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does no...
$24.98
  In Stock
V-Style Drive Belt – Part Number: WH1X2026
V-Style Drive Belt
★★★★★
★★★★★
(8)
PartSelect #: PS270803
Manufacturer #: WH1X2026
This V-shaped drive belt is 29 1/2 inches long x 1/2-inch-wide, and fits both front-load and top-load washing machines. When belts are worn or frayed, they are known to make noise. If you have a top-l...
$14.13
  In Stock
Water Inlet Valve – Part Number: 134190200
Water Inlet Valve
★★★★★
★★★★★
(12)
PartSelect #: PS815509
Manufacturer #: 134190200
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve i...
$127.89
  In Stock
Water Inlet Valve with Outlet Insert – Part Number: WH13X81
Water Inlet Valve with Outlet Insert
★★★★★
★★★★★
(6)
PartSelect #: PS270305
Manufacturer #: WH13X81
This washing machine water inlet valve has two ports for water to enter.
$124.12
  In Stock
Timer Knob with Clip – Part Number: WH1X2757
Timer Knob with Clip
★★★★★
★★★★★
(6)
PartSelect #: PS271127
Manufacturer #: WH1X2757
This part is the replacement timer knob for your washer. It is made of white plastic and is about 1 ¼ inches in diameter. The timer knob sits on the timer shaft and allows you to choose the wash cycle...
  No Longer Available
Compression Ring – Part Number: WH2X650
Compression Ring
★★★★★
★★★★★
(2)
PartSelect #: PS271609
Manufacturer #: WH2X650
This compression ring works in conjunction with the timer dial.
  No Longer Available
Tension Idler Pulley – Part Number: 131862900
Tension Idler Pulley
★★★★★
★★★★★
(5)
PartSelect #: PS418897
Manufacturer #: 131862900
The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell when it is operatin...
$22.06
  Special Order
Screw – Part Number: 131302800
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$11.23
  In Stock
Screw – Part Number: WH2X930
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS271689
Manufacturer #: WH2X930
This screw is sold individually.
$12.24
  In Stock
Washer Lid Lock with External Safety Switch – Part Number: 134101800
Washer Lid Lock with External Safety Switch
★★★★★
★★★★★
(1)
PartSelect #: PS648775
Manufacturer #: 134101800
Mounting bracket on this part replaces old style ( You may need to drill off old bracket before mounting new lock).
  No Longer Available
Four Port Pump – Part Number: WH23X42
Four Port Pump
★★★★★
★★★★★
(2)
PartSelect #: PS271344
Manufacturer #: WH23X42
This washing machine pump is white in color and has four ports for water to pass through.
  No Longer Available
View More
Back to Top

Common Symptoms of models starting with WLW1

[Viewing 8 of 8]
Burning smell
Fixed by
these parts
Fixing Fixing Fixing
Show All
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not agitate
Fixed by
these parts
Fixing Fixing Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing Fixing Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Noisy
Fixed by
these parts
Fixing
Show All
Back to Top
Replacing the Drive V-Belt

Replacing the Drive V-Belt

Replacing the V-Style Drive Belt

Replacing the V-Style Drive Belt

Replacing the D-Shaped Knob Clip

Replacing the D-Shaped Knob Clip

Replacing the Water Inlet Valve

Replacing the Water Inlet Valve

Replacing the Washer Lid Lock with External Safety Switch

Replacing the Washer Lid Lock with External Safety Switch

View More
Back to Top
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replace broken drive belt
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.
Read less
Parts Used:
Drive V-Belt
  • rodney from fairfield bay, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
277 of 309 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
GE washer no spinning during spin cycle
Used the spatula to release the front panel (push flat spatula under top about 2 inches from either side to release the two sprng clips holding the front panel on) to expose the tub and motor assembly. Inspected the belt and it seemed worn and a lot of rubber particles were in base of machine. Ordered the belt from partselect - received it two days later. Loosened 4 motor mount nuts. Removed old belt and replaced. Tightened belt and tightened nuts on motor. Only tricky part is you will need extensions for socket drive because belt is in the way for two of the motor mount nuts. I used a 1/4" small socket wrench, with an extension. No expertise needed on this one.
Read less
Parts Used:
V-Style Drive Belt
  • Laurence from Bronx, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
171 of 190 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer Continued To Fill To Point Of Overflow
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
Read less
Parts Used:
Water Inlet Valve
  • alvaro from east hampton, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
86 of 96 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More
Back to Top