Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The Dryer Thermal Fuse (Thermal Cutoff, Temperature Fuse) is a 2 by ½ inch, white, plastic safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. If the fuse ...
When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas t...
This part replaces your appliances latch (Door Latch Kit, Door Catch, Dryer Door Latch Kit). On your appliance you will find both a strike and a catch. The strike is mounted on the body of the dryer, ...
This Whirlpool Dryer Repair Kit is a convenient solution for fixing noise and drum movement problems in 27-inch dryers. Compatible with models from Whirlpool, Kenmore, Maytag, and more, the kit includ...
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. This part is sold separ...
This Idler Pulley includes the tri-ring and gasket and everything included here is manufacturer-certified. This part maintains correct tension on the drive belt in order to spin the drum properly. If ...
The filter collects lint during the drying cycle. This filter is 12 1/2 inches wide and 10 1/2 inches deep. Replacing the lint filter is an easy repair which requires no tools. When replacing the lint...
The Drive Belt is a 93 1/2" belt which wraps around the dryer drum to allow tension and movement. If broken the dryer will not turn properly, or there may be loud noises. The part is rated as "medium"...
If your dryer will not heat, takes too long to dry, or does not provide enough heat, you might want to replace your igniter kit. This silicone carbide igniter with ceramic holder kit includes the 3-in...
This dryer thermistor is a genuine replacement component designed to monitor and regulate internal temperature in Whirlpool dryers. Mounted on the blower housing, it plays a critical role in controlli...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Fred
January 17, 2025
what side venting kit do I need
For model number WGD8300SW2
Hi Fred,
Thank you for your question. The part number for the side and bottom vent kit is PS3633049. We hope this helps!
Hello Andre, thank you for writing. To fix f1 error on my Whirlpool dryer, start by Resetting Your Dryer.
The first thing to do is to try to reset your dryer, as often this solves the problem. To reset your dryer, simply disconnect the dryer from its power source and leave it turned off for a few minutes. After a few minutes, turn your dryer back on and see if the error code has gone. We hope this helps.
Was this helpful?
Thank you for voting!
Victor
February 5, 2023
Whirlpool dryer when start appear code F01
For model number WGD8300SW2
Hello Victor, thank you for reaching out. The error code F01 indicates an issue with the Control Board, part number PS11748354. We recommend you first reset the dryer. For this, simply disconnect the dryer from its power source and leave it turned off for a few minutes. After a few minutes, turn your dryer back on and see if the error code has gone. If the problem does not resolve, we suggest you check the following internal components: Thermal Fuse, part number PS11741460, and Thermostat, part number PS11746740. We hope this helps!
I'm looking for a part, but I'm not sure what part to get. My Whirlpool drum is not spinning and when it does it's spinning slow what part I should replace .
For model number WGD8300SW2
Hello Stacey, thank you for your query. Based on our research, you may need to replace the dryer repair kit, part number PS373088, to fix the issue. This kit contains a multi rib dryer belt, 4 drum support rollers, 1 idler assembly, 9 tri rings, and 1 washer. This kit needs to be replaced due to normal wear and tear. We hope this sorts out your problem!
Hi Sam,
Thank you for your question. If the dryer is not producing heat, the issue may be with the thermal fuse. Unplug the dryer from the electrical outlet to remove the thermal fuse from the dryer, so you can test it for continuity with a multimeter on the Rx1 setting. If you receive a reading other than zero or infinity, there is no continuity and you need a replacement thermal fuse. If the thermal fuse is fine, check the coils that operate the gas valve with the multimeter. If you receive any reading other than 1000-2000 ohms of resistance, you need replacement coils. We hope this helps!
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils. Not knowing what the problem was I started looking at the coils and could not see any broken parts. So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of
... Read moreneedle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading. I replaced with a new one and put it all back together the way I took it apart. Then I plugged it in and it worked first time, I now have warm dry clothes.
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.
Ascertaining the problem was the most time consuming part.
The actual repair was quite simple and did
... Read moren't take but 15-20 minutes.
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.
