WF409ANR Samsung Washer - Overview
Sections of the WF409ANR
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Inlet Hose - 5 FT
PartSelect #: PS11746820
Manufacturer #: WP89503
This hose can handle hot or cold water and is five feet long.
$19.30
In Stock
Hex Head Bolt
PartSelect #: PS4205366
Manufacturer #: DC60-40137A
This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing...
$12.85
In Stock
Shock Damper Rear
PartSelect #: PS4212220
Manufacturer #: DC66-00470B
Got a problematic Whirlpool stove at home? We have the solution for you ? the Whirlpool BURNR-HEAD Base Burner (Large). It's more than just a replacement part; it's the key to getting your appliances ...
$49.50
On Order
Shock Damper Front
PartSelect #: PS4212219
Manufacturer #: DC66-00470A
This is an individually sold front shock absorber designed for use with Samsung dryers. Shock absorbers are used to distribute the weight of the dryer drum evenly and ensure that the different bumps a...
$79.80
On Order
Outer Seal Clamp
PartSelect #: PS4218211
Manufacturer #: DC97-04973B
This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made o...
$13.92
In Stock
Door Switch Assembly
PartSelect #: PS4210737
Manufacturer #: DC64-00519B
This is a door switch assembly designed for Samsung washing machines. This door switch assembly is used to latch and lock the door shut before the washing cycle commences and communicates with the con...
$45.29
In Stock
Water Valve
PartSelect #: PS4209100
Manufacturer #: DC62-30314K
One solenoid valve for hot water
$96.17
In Stock
Flange and Shaft Assembly
PartSelect #: PS4220876
Manufacturer #: DC97-15491A
Introducing a high-functioning and genuine Samsung replacement part, a Washer Inner Tub Flange and Shaft Assembly. This essential piece aids in connecting the spin basket to the drive motor, allowing ...
$243.40
In Stock
Washer Bolt Assembly
PartSelect #: PS4217876
Manufacturer #: DC97-02412A
Assembly BOLT;SWF-P12,MOTOR/
$26.82
In Stock
Door Glass
PartSelect #: PS4210731
Manufacturer #: DC64-00504C
Explore the sturdiness and functionality of the Samsung Washer Door Glass. Fitting perfectly with a set of Samsung Washer models, it is a high-quality door glass, designed with an eye for detail by Sa...
$172.08
On Order
Water Temperature Thermistor
PartSelect #: PS4214274
Manufacturer #: DC90-10128N
The thermistor monitors and helps regulator the water temperature in the washer.
$63.64
In Stock
Questions And Answers for WF409ANR
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WF409ANR
[Viewing 5 of 5]Shaking and Moving
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The washing would stop in mid cycle and the door would be locked.
An initial issue was getting the door to unlock. I tired several things but finally was able to pull the door as if to open it and put something between the door handle and the front of the washer while I ran a washer cycle. There is a way to take the washer top off and reach down inside the unit and pull down on a release, but I did no
... Read more
t try that.
The washer has a rubber boot between the washer frame and the wash tub. There is a metal wire ring that secures the outer edge of the boot to the washer frame. Peel back the outer edge of the boot at the bottom to reveal a metal ring that has its ends connected by a small spring. Use a flat tip screw drive to pry this ring off. Peel back the boot from the washer frame.
Next use a Phillips screw drive to remove the two screws that protrude through the wash frame on the right side of the door.
Reach between the washer tub and the frame and the tub and pull the switch through the opening and the washer tub. You will have to wiggle the switch around to remove it. There are three sets of wires attached to the switch by plugs.
The switch is covered with a plastic protective cover. Remove this. You will have to use a screw driver to release various catches to do this.
Remove the three set of wires. There are catches that secure the wire plugs in place. pry them back with a small screw drive.
Attach the new switch to the sets of wires.
Attach the protective cover to the switch. The wires feed through a small slot toward the bottom of the switch.
Slide the switch through the opening where you removed it. and re-attach it using the two screws.
Put the rubber boot in the channel in the washer frame. Replace the metal ring. This was the most challenging part of the repair for me. I had to play around with this to get it into position. You have to work it around the gasket and stretch out the spring.
By the way, The service was great and exceeded by expectations.
The washer has a rubber boot between the washer frame and the wash tub. There is a metal wire ring that secures the outer edge of the boot to the washer frame. Peel back the outer edge of the boot at the bottom to reveal a metal ring that has its ends connected by a small spring. Use a flat tip screw drive to pry this ring off. Peel back the boot from the washer frame.
Next use a Phillips screw drive to remove the two screws that protrude through the wash frame on the right side of the door.
Reach between the washer tub and the frame and the tub and pull the switch through the opening and the washer tub. You will have to wiggle the switch around to remove it. There are three sets of wires attached to the switch by plugs.
The switch is covered with a plastic protective cover. Remove this. You will have to use a screw driver to release various catches to do this.
Remove the three set of wires. There are catches that secure the wire plugs in place. pry them back with a small screw drive.
Attach the new switch to the sets of wires.
Attach the protective cover to the switch. The wires feed through a small slot toward the bottom of the switch.
Slide the switch through the opening where you removed it. and re-attach it using the two screws.
Put the rubber boot in the channel in the washer frame. Replace the metal ring. This was the most challenging part of the repair for me. I had to play around with this to get it into position. You have to work it around the gasket and stretch out the spring.
By the way, The service was great and exceeded by expectations.
Read less
Parts Used:
-
Arthur from WILLARD, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
6 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking water inlet hoses.
-
Helen from NASHUA, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Parts Used:
-
Jimmy from MEMPHIS, TN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!