WF316LAW Washer - Overview
Models starting with WF316LAW
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Washer Door Lock Latch
PartSelect #: PS11745016
Manufacturer #: WP8182634
This washer door lock and switch assembly is a critical safety and control component for front-loading washing machines. It secures the door during wash and spin cycles, preventing accidental opening ...
$77.66
In Stock
Washer Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$7.30
In Stock
Door Lever
PartSelect #: PS11741552
Manufacturer #: WP34001260
Also known as a door strike.
$51.97
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$9.40
In Stock
Affresh Washing Machine Cleaner - 3 pack
PartSelect #: PS1960673
Manufacturer #: W10135699
Having trouble with your freezer?s efficiency? Your GE Freezer Door Gasket might be the solution you?re looking for. This is an official replacement part designed to perfectly seal your freezer door. ...
$19.89
Special Order
Drain Pump Assembly - 120V 60Hz
PartSelect #: PS4204638
Manufacturer #: DC31-00054A
This is a 120 volt, 60 hertz drain pump assembly for a washing machine. It is a genuine OEM part. This pump helps expel water from the washing machine, and is activated after the spin speed is maintai...
No Longer Available
Hex Head Bolt
PartSelect #: PS4205366
Manufacturer #: DC60-40137A
This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing...
$12.55
On Order
Shock Damper - Front
PartSelect #: PS11741563
Manufacturer #: WP34001303
This part helps keep the washer from vigorous shaking during its cycles. They are sold individually. They mount to the front half of the outer tub. Appliance would take 2.
$79.10
In Stock
Door Switch Assembly
PartSelect #: PS4210737
Manufacturer #: DC64-00519B
This is a door switch assembly designed for Samsung washing machines. This door switch assembly is used to latch and lock the door shut before the washing cycle commences and communicates with the con...
$44.24
In Stock
Water Valve
PartSelect #: PS4209100
Manufacturer #: DC62-30314K
One solenoid valve for hot water
$93.95
In Stock
Door Boot Seal
PartSelect #: PS2037232
Manufacturer #: 34001302
Also known as a bellow. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
$161.68
On Order
Common Symptoms of models starting with WF316LAW
[Viewing 8 of 8]Lid or door won’t close
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
front load washer latch replacement
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using to ... Read more p opening.
7. reverse order to finish.
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using to ... Read more p opening.
7. reverse order to finish.
Read less
Parts Used:
-
James from Vilonia, AR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
196 of 240 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door lock was in the locked position and door could not close
I bought a new door lock for 132 dollars (item number PS2037196).
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the bac ... Read more k of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that.
(there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that.
You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble.
(Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
Thats it.
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the bac ... Read more k of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that.
(there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that.
You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble.
(Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
Thats it.
Read less
Parts Used:
-
Suryakant from Cortlandt Manor, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
67 of 74 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door latch split
replaced door latch but door would not close had to remove latch assembly and reset the latch in the latch assembly. To reset latch in latch assembly you remove the black plastic only on latch assembly then press the spring down with thumb move the black plastic catch back to the latch position. when you remove the black plastic there is
... Read more
four metal switchs and one spring that you have to pay attention too so remove very carefully.
Read less
Parts Used:
-
Leon from North Platte, NE
-
Difficulty Level:Very Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
51 of 64 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!