Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WEF360ESD

WEF360ESD Westinghouse Range - Overview

Get Parts and Repair Help for WEF360ESD

If you know the range repair part you need, you can browse the list of all parts on the WEF360ESD, or you can search by name or part description. You can also find your part by where it is located on the WEF360ESD by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for WEF360ESD parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the WEF360ESD

[Viewing 5 of 5]

Manuals & Care Guides for WEF360ESD

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.15

Bake Element - Push On Terminals - 240V

This bake element is used in electric ovens and ranges. It can be found in the bottom of the appliance. It supplies the heat required for the baking function. If your element is no...

$23.30

Infinite Burner Switch - 8" - 240V

The infinite burner switch controls the stove top eight-inch surface burner, which is the large surface element. If your surface element is not warming up, the element can be tested to determine whether or not it is defective. If your element is not defective, then it is more than likely that the infinite burner switch is the issue. Before you install the infinite burner switch you will need to unplug your range from the power supply, or shut off the home circuit breaker. The tools you will need to do this repair include a number one square head screwdriver and a pair of needle nose pliers.

$28.81

Oven Temperature Sensor

The temperature sensor detects the temperature within the oven cavity. If there is a limited amount of heat, it is not heating evenly, or the oven will not start, this might indica...

$29.34

Infinite Burner Switch - Small Element - 240V

This is a part for your range. This switch controls the stovetop surface burner. If you notice that your stove top is not turning on or is not adjusting to the corresponding desired heat, it is mostly likely due to the burner switch needing to be replaced. You will need a #1 square-head screwdriver and needle-nose pliers. Disconnect the power from the range. You will need to move the range out from the wall to remove the upper back panel to access to this part. This is an OEM genuine part.

$3.62

Main Terminal Block Kit

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryer...

$5.56

Indicator Light Lens

This is a red indicator light lens for an oven that covers the indicator light for the surface element. The indicator light signifies when the element is on and heated. This part is sold individually. It is recommended to check other red indicator lights in case they need to be replaced because they often wear at the same rate. It is difficult to see the light without the red lens. This part does not include the light. If your light does not illuminate, you may want to consider ordering the light as well. Tools required for this repair are a 1/4 inch nut driver and a stubby Phillips screwdriver.

$8.93

Rear Drawer Glide

This rear drawer glide, also known as a storage drawer glide, is used in ranges. This helps hold the front side of the storage drawer and allows the drawer to easily slide in and o...

$124.82

Broil Element - 2400W

This part goes inside of your oven at the top.

$8.93

Front Drawer Glide

The front storage drawer glide on your range is mounted on the side of the cabinet. The purpose of the drawer glide is to support the storage drawer from the front. If your front s...

$8.35

Anti-Tip Kit

The anti-tip bracket kit comes with one metal bracket and two installation screws, and is sourced directly from the genuine manufacturer. It prevents the freestanding oven, range, or stove from tipping when force or weight is applied to an open oven door. The bracket is secured to the floor and wall and fits over the rear leveling leg in the back of the appliance, in a cutout specifically designed for the anti-tip bracket. This part is very essential to the safe operation of the appliance. Failure to install the bracket properly can result in the oven tipping or falling and causing injuries.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven woudn't heat

  • Customer: David from Shawnee, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1119 of 1160 people found this instruction helpful
1. Removed two screws, pulled out the element, voltage tested the element and determined it was an open circuit (bad element).
2. Ordered the part from partselect.com
3. Disconnected element, connected the new one, and screwed it back in. read more

Element cracked in two pieces

  • Customer: Michael from Green Bay, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 716 of 811 people found this instruction helpful
Shut off circuit breaker to stove and collected the tool from the basement. Turned on flashlight. Unscrewed the two hex nuts from the old element/back of the oven. Slid the old element prongs out of the back, exposing the connecting wires. Pulled the connecting wires off of the old element, carefully, so that the connections wouldn't come off of the w... read more

oven did not heat

  • Customer: jack from chambersburg, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 415 of 425 people found this instruction helpful
removed screws pulled element out. removed wire from old element replaced with new element.very easy read more