Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
This manufacturer-certified heating element is used to create heat during the dry cycle and increase water temperature during portions of the wash cycle when certain options are selected. If your dish...
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
This dishwasher filter is a genuine OEM component designed to work with the water pump, preventing debris from entering and potentially damaging the pump system. Made with a gray plastic top and botto...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element.
This door gasket is a genuine OEM replacement part that is specially designed for your dishwasher. The gasket is located around the frame of the dishwasher. It is a rubber seal that helps prevent wate...
This part is used to hold the access panel in place. Sold individually.
$6.25
In Stock
Order now and your part arrives by Mar 19
Questions And Answers for WDF520PADM3
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Travis
December 17, 2019
Dishwasher has 4 cycles, but it will only let me select 2: 1 hour wash and soak and clean. I cannot select heavy or normal wash cycles. any ideas?
For model number WDF520PADM3
Hi Travis,
Thank you for your question. If both the 1 hour wash and the soak and clean options on the control panel are not working, the issue could be either the buttons, part number PS11731106, or the electronic control board, part number W10804115. You will need to check both parts to see which one is causing the issue. We hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Pamela
August 24, 2022
Washer goes through entire cycle but at the end water stays in bottom
For model number WDF520PADM3
Hi Pamela,
Thank you for your question. It is normal for a small amount of water to remain in the bottom of the dishwasher. Usually a cup of water will remain. This keeps the seals and working parts in good condition. If it is more than that, you will need to check the drain pump, the drain hose and the electronic control board. We have included a link that you may reference on how to check these parts. Once you have determined the part you need, please feel free to call customer service. We are open 7 days a week and anyone will be happy to assist you. We look forward to hearing from you!
Need part for for panel switch, start switch stopped working
For model number WDF520PADM3
Hello Jo, thank you for the question. According to our research, the start switch does not come separately. You may need to order the electronic control board, part number PS11722932. We hope this helps!
Options button for Heat Dry & High Temp does not allow me to select either option.
For model number WDF520PADM3
Hello Adam, Thank you for your inquiry. First, we recommend checking the button tree to make sure that those buttons are not damaged. Next, try resetting the control board by disconnecting the power to the dishwasher (either by unplugging it or turning it off at the circuit breaker) for 10 minutes. If that does not fix the issue, then you may need to replace the control board. Good luck with your repair.
Dishwasher will not start! The touchpad lights up when I select different modes! But the touchpad does not light up on the start button!???????
For model number WDF520PADM3
Hello William, thank you for getting in touch. According to our research, the issue is most probably with the control board, part number PS11722932. You may need to replace it to fix the issue. We hope this solves your problem!
I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!
Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls
... Read more out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.
