Models
>
WA4721
WA4721 Maytag Washer - Overview
Sections of the WA4721
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
V-Style Drive Belt (32.5 inches long)
PartSelect #: PS11740616
Manufacturer #: WP28808
This v-style drive belt is thirty-two and a half inches long and half of an inch wide.
$43.27
In Stock
Complete Hub and Seal Kit
PartSelect #: PS2174602
Manufacturer #: R9900552
This kit comes with hub, seal head, gasket, seal shroud, seal seat, screw, spline insert, drive bell and seal.
No Longer Available
V-Style Cogged Pump Belt (22.5 inches long)
PartSelect #: PS11740600
Manufacturer #: WP27155
This V-style cogged tooth pump belt is used in conjunction with the drive belt in your washing machine. This belt is all black in color and is made entirely of rubber. It is twenty-two and a half inch...
$39.81
Special Order
Drain Pump - 2 Port
PartSelect #: PS2034294
Manufacturer #: 31969
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
No Longer Available
Idler Pulley Wheel
PartSelect #: PS11740614
Manufacturer #: WP28800
This idler pulley wheel is not quite three inches in diameter. It is black and made of plastic with a metal center.
No Longer Available
Questions And Answers for WA4721
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WA4721
[Viewing 5 of 5]Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Frayed V-belt
VERY EASY!!!
SAFETY FIRST-Always unplug the appliance.
Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, r ... Read more emove 4 mounting bracket screws that secure the motor and pump assembly. Pull back the tension/idler pulley to loosen belt off the main pulley to the washer drum. Tilt and pull out motor/pump assembly. Underneath the pump, use star-bit to remove the pump from motor assembly to remove the belt. Install new belt on motor pulley (Good time to check for debris or anything restricing free movement of pump) and re-install pump. Install the motor/pump assembly and loosely secure the motor/pump assembly. Place the belt onto the motor pulley and pull back the tensioner/idler pulley to allow slack of belt to be placed on washer drum pulley. Put the belt on the lip of the drum pulley and rotate while pulling back the tensioner/idler pulley until the belt is seated on the groove of the drum pulley. Tighten the motor/pump assembley. Re-attach the 2 hoses and tighten down the clamps. Re-connect the electrical connector to the motor...Don't forget to plug in the washer and secure the front panel...Piece 'O cake, you're done! About 15 minutes to do the job. Much like changing a belt on most vehicles.
SAFETY FIRST-Always unplug the appliance.
Use 8mm socket to remove front panel screws. Loosened up two hose clamps connected to the pump and removed both lines (Hoses contain water, use a towel) which is located underneath the motor. Disconnect motor electrical connector on the left side of the motor. With socket, r ... Read more emove 4 mounting bracket screws that secure the motor and pump assembly. Pull back the tension/idler pulley to loosen belt off the main pulley to the washer drum. Tilt and pull out motor/pump assembly. Underneath the pump, use star-bit to remove the pump from motor assembly to remove the belt. Install new belt on motor pulley (Good time to check for debris or anything restricing free movement of pump) and re-install pump. Install the motor/pump assembly and loosely secure the motor/pump assembly. Place the belt onto the motor pulley and pull back the tensioner/idler pulley to allow slack of belt to be placed on washer drum pulley. Put the belt on the lip of the drum pulley and rotate while pulling back the tensioner/idler pulley until the belt is seated on the groove of the drum pulley. Tighten the motor/pump assembley. Re-attach the 2 hoses and tighten down the clamps. Re-connect the electrical connector to the motor...Don't forget to plug in the washer and secure the front panel...Piece 'O cake, you're done! About 15 minutes to do the job. Much like changing a belt on most vehicles.
Read less
Parts Used:
-
John from Milton, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
60 of 67 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Seal On The Bottom Of The Tub Was Leaking
Removed the front of the washer, then lifted the top up and held it up with a prop. Pulled the agitator straight up and started the disasembly. Using the photos in the hub and seal kit was a big help. The large nut on the output shaft had to be cut off with my dremel tool and the hub removed with a wheeler puller. Assembly was pretty
... Read more
much straight forward. Primed the pump and started the machine for the stated time and was a sucess.
Read less
Parts Used:
-
HOWARD from CORTLAND, OH
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
33 of 42 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
tub leaking water
Took off the agitator, removed inner tub, exposing the hub drive. Found fusion between hub drive and agitator shaft. Rather than using a wheel puller as instructions recommended I got my masonry hammer and removed the drive hub in pieces. Removed debris from the tub. Installed sealant around lower seal as instructed. Re-assembled inne
... Read more
r tub, agitator with new upper seal. Plugged in the washer, turned on the water. No leak. Happy happy.
Read less
Parts Used:
-
Raymond from East Sandwich, MA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Socket set, Wrench set
18 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!