Models > WA45H7000AW > Instructions

WA45H7000AW Samsung Washer - Instructions

All Instructions for the WA45H7000AW
1 - 11 of 11
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Easy instal, taking off entire back panels of appliance is required
Shut off water and electrical supply to appliance, take water supply hoses off to allow for proper access to back of machine.
Take off back panels of appliance. Disconnect two hoses from pump. Take out two screws which attach pump to washer body. Detach wiring which connects pump to control unit ( that takes a little time). Install pump in designated location, connect hoses, connect wiring to control unit, connect appliance to powere source, test run to make sure everything works properly, make final detailed wire connection Pump to control unit, install back panels, Connect water supply hoses .....and be proud of yourself!
Parts Used:
Washer Drain Pump Assembly
  • Dieter from CHICAGO, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top Load washer would not drain to complete spin cycle.
Though I could hear and feel the drain pump running, the washer would not drain. This model does not have a filter for the drain pump. I lowered the discharge hose from the stand up pipe on the wall, and lowered it to the floor. Water ran right out, so no blockage in the drain system. After removing the inlet and outlet hoses to the pump, a quick inspection showed the impeller on the motor was off the shaft and flopping around. Bingo, motor runs but cant pump.
Ordered from Partselect and received in ONE DAY. I really didn't want to go back to it that soon, but they certainly did their part. Ha. Thank you all. Greg
Parts Used:
Washer Drain Pump Assembly
  • Greg from Medina, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer stopping in the rinse and spin cycle
Tipped the washer up on a couple of chairs. Pulled the motor apart in three pieces and replaced the Hall Sensor. Error code lead me right to the problem and solution.
Parts Used:
Motor hall sensor
  • Gary from CENTER HARBOR, NH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The cap came off somehow
Just snapped on part in the center of tub where it belongs
Parts Used:
PULSATOR-CAP
  • James from GALLATIN, TN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pulsator cap broke off.
The cap was easily replaced by hand and pops right in place.
Parts Used:
PULSATOR CAP;ALL USA MODEL(EXCEPT 3000J)
  • tommie from MURFREESBORO, TN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pulsator- Cap, two of three that that attach the cap the the tub were broken off.
Snapped the replacement cap in place.
Parts Used:
PULSATOR-CAP
  • Michael from ROCKFORD, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pusator-cap was missing - Kids swore they didn't do it
Insert Tabs A into Slots B. Twist.
Parts Used:
PULSATOR-CAP
  • John from LA MIRADA, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pulsator cap pins broke off leaving the screw head exposed.
Nothing to it, just aligned the three pins on the new cap and gently
pushed down.
Parts Used:
PULSATOR-CAP
  • Bonnie from Houston, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer will not drain
Went to YouTube video and followed instructions.

Hardest part was making sure water from hose does not flood floor while taking it off from water pump and letting water drain in bucket.

See YouTube video

https://youtu.be/oOnxbj-unfc?si=OFFwOcNiIymh_9b-
Parts Used:
Washer Drain Pump Assembly
  • Alpha from JACKSONVILLE, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pulsator Cap came off during a Wash cycle, it was not usable as part of it was broken
just popped the new one in, it took all of 3 seconds....the worst part was that the part was all Plastic and the replacement part cost close to $70 including Shipping. the part was no bigger than the Cap on a LG bottle of Orange Juice.....Ridiculous..
Parts Used:
PULSATOR CAP;ALL USA MODEL(EXCEPT 3000J)
  • donald from ROCHESTER, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain hose was cracked and leaking.
Squeezed clamp with fingers to remove old drain hose. Put clamp on new replacement hose and slid over drain pipe and released clamp. Less than a minute. Hose was exact replacement part.
Parts Used:
Assembly HOSE(O);HUDSON WASH
  • Richard from HERNANDO, MS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WA45H7000AW
1 - 11 of 11
Back to Top