Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
This filter is made of metal and is intended for use with ranges and cooktops. Grease filters are an important but often neglected part of ranges. If the filter is full, your extractor fan will become...
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of...
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
This door strike is less than an inch long. It is all white in color and it is made entirely of plastic. The door strike fits on the inside of your range and is the locking mechanism that latches to t...
This oven control board and clock is for ranges.
Oven control board and clock monitors the oven temperature and controls the oven heating functions in the range, and includes the digital display fo...
This gas valve knob measures approximately 2 12 inches in diameter. It is a black knob that has white lettering aroud its perimeter denoting the different temperature levels: low, medium, high, etc. T...
This black front burner assembly is a precision-engineered component designed for use with select gas ranges. Measuring nine inches in diameter, it provides reliable and consistent heat distribution f...
This rear burner assembly directs gas to the burner head for even heat distribution. Finished in glossy black, it replaces worn or faulty parts that cause ignition or heating issues. Installation requ...
If your oven isn’t heating properly or your food is cooking unevenly, this bake element might be the solution. It’s the part at the bottom of the oven that heats up when you bake or roast. With 2800 w...
$82.24
In Stock
Order now and your part arrives by May 17
Questions And Answers for SVD48600BC
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening,
... Read morereinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Removed the 4 phillip head screws that hold the trim plate on the bottom of the display panel (and you probably could skip this step). Next, I removed the knobs from the front of the display panel. Then I removed the 4 phillip head screws that were located (1 each) behind the knobs. Finally, I removed the 4 hex head screws
... Read morefrom the bottom of the front panel. You caan then remove the panel a few inches and remove the two cable connectors. The trick part is to get the flat ribbin cable disconnected. If you squeeze the two small tabs (one on each end of the connector), the connector moves up and spreads open to CAREFULLY remove the ribbon cable. The clock assembly has just two hex head screws holding it in place. Remove them, and reassemble everything in reverse. If you did everything correctly, you should have a very bright stove clock again!
