STP26DA-0 Maytag Range - Overview
Sections of the STP26DA-0
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Range Suface Burner Ignition Switch
PartSelect #: PS11742283
Manufacturer #: WP4157180
When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.
$59.47
Special Order
Oven Seal - Top or Bottom
PartSelect #: PS1757448
Manufacturer #: Y07623602
This piece of oven door seal has a metal hook on each end. This seal is compatible with the top and the bottom of the oven door window.
No Longer Available
GRATE, 7"" ROUND BURNE
PartSelect #: PS1757350
Manufacturer #: Y07540300
This round gas burner grate is black in color and has a diameter of just under seven inches. This burner grate is intended for use with Amana brand gas ranges.
No Longer Available
Side Oven Door Seal
PartSelect #: PS11757501
Manufacturer #: WPY07623603
This single oven door side seal is fourteen inches long. It is made of black rubber and it has a metal hook in each end.
No Longer Available
Spark Module
PartSelect #: PS2033659
Manufacturer #: 31829401
The color of the original part or the part you receive may be different from the pictured part. This is still the correct part.
No Longer Available
Bake or Broil Spark Igniter
PartSelect #: PS11757497
Manufacturer #: WPY07491300
This part is found in your gas range, also known as spark electrode. This part helps your burner ignite and produce flame. This will need to be replaced if it is no longer providing spark to start the...
No Longer Available
Surface Burner Valve
PartSelect #: PS12597419
Manufacturer #: 07454107
Valve, top burner 90
No Longer Available
Questions And Answers for STP26DA-0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the STP26DA-0
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
electric ignite gas stove kept clicking the ignitor unless unplugged from electrical outlet
I removed the 2 screws that held the housing on at the back of the stove. Then I removed the 2 screws that held the module to the back of the stove. Since I am not an experienced electrical person (I am a female nurse in the operating room), I unplugged 1 wire at a time from the old module and plugged it into the new module. I repeated th
... Read more
is step with each wire to make sure I didn't put the wrong wire on a wrong spot until I had all the wires to the new module. Then reattached the screws, plugged in the oven and presto, it works just fine! Was amazed at how easy it was. A 50 dollar part instead of a new 1500 dollar stove. How easy is that?
Read less
Parts Used:
-
Diana from Jacksonville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
10 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ignitor did not spark when turning the know
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that atta
... Read more
ch to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.
Read less
Parts Used:
-
Richard from Lansing, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
9 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Left rear burner would not ignite
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours.
... Read more
John, N.J.
Read less
Parts Used:
-
John from Perth Amboy, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!