SRU55T04EU Bosch Dishwasher - Overview
Models starting with SRU55T04EU
Click on the best match to narrow your results.
- SRU55T04EU (23) Bosch Dishwasher (Bosch Dishwasher Model SRU55T04EU/23 Parts)
- SRU55T04EU (28) Bosch Dishwasher (Bosch Dishwasher Model SRU55T04EU/28 Parts)
- SRU55T04EU (21) Bosch Dishwasher (Bosch Dishwasher Model SRU55T04EU/21 Parts)
- SRU55T04EU (15) Bosch Dishwasher (Bosch Dishwasher Model SRU55T04EU/15 Parts)
- SRU55T04EU (29) Bosch Dishwasher (Bosch Dishwasher Model SRU55T04EU/29 Parts)
- SRU55T04EU (26) Bosch Dishwasher (Bosch Dishwasher Model SRU55T04EU/26 Parts)
Keep searches simple, eg. "belt" or "pump".
Lower Rack Wheel with Clip
PartSelect #: PS8697067
Manufacturer #: 00165314
This dishrack wheel is designed for use on the lower rack of your dishwasher, it allows the rack to roll in and out of your appliance with ease. This roller wheel includes the locking clip required fo...
$12.80
In Stock
SEALING
PartSelect #: PS18375762
Manufacturer #: 12054183
This seal is also referred to as a door gasket, and it is designed for use on dishwashers. It is installed on the door of the appliance, and it seals the space between the tub of the dishwasher and th...
$17.28
In Stock
FILTER-MICRO
PartSelect #: PS17645489
Manufacturer #: 17008311
This dishwasher micro filter is designed to trap food particles, grease, and debris before they can recirculate through the wash system, helping maintain clean water flow and effective cleaning perfor...
$76.26
In Stock
Dishrack Stopper Kit
PartSelect #: PS8697039
Manufacturer #: 00165254
A holder is used in dishwashers, it is known as the dishrack stop kit. This kit comes with both the front and the rear stop, these parts are installed at either end of the rails that the upper rack sl...
$14.72
In Stock
Drain Hose
PartSelect #: PS8703123
Manufacturer #: 00298564
This drain hose is designed for use in dishwashers. After the wash cycle is complete the water need to leave the dishwasher, this drain hose it carries the dirty water from the drain pump to the kitch...
$31.99
In Stock
Detergent and Rinse Aid Dispenser
PartSelect #: PS8722285
Manufacturer #: 00490467
This detergent and rinse aid dispenser is an important part in your dishwasher. It is located on the inside of the door and it holds and releases the detergent during the wash cycle of your dishwasher...
No Longer Available
Check Valve
PartSelect #: PS8697043
Manufacturer #: 00165262
This check valve is a genuine OEM part that is compatible with several different makes and models of dishwasher. A check valve is designed to prevent the backflow of dirty water, food waste, and debri...
$11.53
In Stock
Dishwasher Tripping Device
PartSelect #: PS8697162
Manufacturer #: 00166630
Ensure proper detergent release during wash cycles with this genuine latch kit, designed to open the detergent cup at the right time and prevent premature opening. The kit includes a latch, spring, an...
$17.91
On Order
LID
PartSelect #: PS8697157
Manufacturer #: 00166623
This OEM-sourced detergent dispenser cover, also known as a rinse aid dispenser lid, seals and protects the detergent compartment in your dishwasher. Typically located on the inner door, it covers the...
$12.16
On Order
LID
PartSelect #: PS8697155
Manufacturer #: 00166621
This dishwasher detergent dispenser cover helps seal the detergent compartment and ensures detergent is released at the correct point during the wash cycle. Designed with an integrated gasket for a se...
$54.67
In Stock
On/Off Push Button Switch
PartSelect #: PS8713809
Manufacturer #: 00424410
This on/off main switch is designed to control the electrical power to your dishwasher with a simple push-button action, providing reliable operation and smooth response. Made of durable plastic in a ...
$62.67
In Stock
Common Symptoms of models starting with SRU55T04EU
[Viewing 9 of 9]Leaking
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Spring assembly on detergent and rinse aid dispenser broke so the sliding lid would not operate
Here are the steps you need to take to do the job properly:
1. turn off electrical circuit breaker to the dishwasher
2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed.
3 ... Read more . unplug the wiring harness to the detergent/rinse aid dispenser
4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser.
5. the unit will pop out toward the inside of the dishwasher
6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in.
7. re-attach the wiring harness
8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job.
9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks.
10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.
1. turn off electrical circuit breaker to the dishwasher
2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed.
3 ... Read more . unplug the wiring harness to the detergent/rinse aid dispenser
4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser.
5. the unit will pop out toward the inside of the dishwasher
6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in.
7. re-attach the wiring harness
8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job.
9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks.
10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.
Read less
Parts Used:
-
Steven from SUWANEE, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
18 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher not draining
I used a wet vac to remove the water from the dishwasher. remove cover and filter/strainer from bottom of dishwasher. remove screw which allows you to lift the plastic piece to access check valve. Original check valve looked like new , I installed new check valve re installed parts . Job done and issue resolved .
Parts Used:
-
Bruce from MOUNT VERNON, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
14 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
BROKEN CORD, PART OF DOOR COUNTERWEIGHT
REMOVED DISHWASHER FROM CABINET. DETACHED BASE FROM BODY OF THE DISHWASHER. INSTALLED NEW CORD, REATTACHED BASE TO BODY OF DISHWASHER AND REINSTALLED IN CABINET. OPINION: THIS IS A LENGTHY REPAIR AND UNNECESSARY ONE. THE CORD IS PART OF THE DOOR COUNTERWEIGHT AND SUBJECT TO TENSION EVERY TIME THE DOOR IS OPENED, AS WELL AS POTENTIAL CHAF
... Read more
FING DUE TO PROXIMITY TO VARIOUS METAL PARTS, AND VIBRATION. THE CORD SHOULD BE MADE OF STRONGER MATERIAL AND ARMORED OR ALLOWED MORE CLEARANCE. BOSCH SHOULD FIX TO LAST THE LIFE OF THE DISHWASHER.
Read less
Parts Used:
-
Bill from EAST JORDAN, MI
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Wrench set
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!