This is a replacement dishrack roller or wheel for your dishwasher. It is made of gray plastic, measures a little over an inch in diameter, and is sold individually. This roller is designed for the lo...
This part is a replacement tine row clip for your dishwasher. The tine row clip is adjustable, and it fits onto your dishrack to holds the tines into place. If your dishrack tine rows will not stay in...
This kit includes 2 spring and 2 cables. This door spring kit is for dishwashers.
Door spring kit applies tension to the dishwasher door through the door hinge to prevent the door from dropping t...
This seal is also referred to as a door gasket, and it is designed for use on dishwashers. It is installed on the door of the appliance, and it seals the space between the tub of the dishwasher and th...
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Andrew
September 30, 2023
Dishwasher fills with water and then starts beeping, when opened the water tap light is lit but no error code. Resets and drains fine. Checked both drain filters amd cleaned and problem still persists. Frustrating and I don't want to just start throwing parts at it please advise!
For model number SHX68T55UC
Hi Andrew, thank you for reaching out. First, you may need to make sure that the supply hose is not kinked or blocked. If that is not causing the issue, then you may need to check the water inlet valve, part number PS16746057, as it is most likely faulty and may need to be replaced. We hope this helps!
the label only states SHX68T55UC
how do i know if I have:
Bosch Dishwasher SHX68T55UC /01 or /02 or /07 or /09 ?????
are the parts different?
For model number SHX68T55UC
Hello Ted, thank you for your inquiry. We would need the part you are looking for to compare with each one. Please feel free to give us a call. We look forward to hearing from you.
Was this helpful?
Thank you for voting!
Ed
January 13, 2023
Washer stops mid-cycle, but will continue after opening and pressing start again. I had this problem before, and the consultant gave me a series of steps to reset it, but I don't remember how. I also want the manual. Thank you, Ed
For model number SHX68T55UC
Hi Ed,
Thank you for your question. If your dishwasher stops mid-cycle, there are some parts that you will need to check to see which one is causing the issue. You will need to check the door latch and switches, the electronic control board, the control panel and the heat pump. We have included a link that you may reference on how to check these parts. Once you have determined the part you need, please feel free to call customer service. We are open 7 days a week and anyone will be happy to assist you. We look forward to hearing from you!
When running, I can see water flow down overflow channel to the pan at bottom of machine which trips the foam-pad / float-valve at the bottom.
The problem is that I can't figure out where the water is coming from. I've recently replaced the door seals, so not that. I suspect the machine is overfilling as the depth of the water in machine looks excessive. So perhaps there's a sensor / switch failing somewhere. Would welcome any suggestions
For model number SHX68T55UC
Hello Lindsay, thank you for the question. The water inlet valve, part number PS16746057, is an electrically-controlled valve that opens to allow water to enter the dishwasher. A faulty inlet valve can result in water overflow in the dishwasher you may need to replace the water inlet valve. Also, check the float switch, part number PS8728720. The float lifts as the water level in the dishwasher rise, and when the proper water level is reached, the stem of the float activates the float switch to turn off the water inlet valve. A malfunctioning float or float switch could cause the water level to be too high and create a leak. We hope that helps!
There is a white part that attaches to the back of the second rack. This part fits into back panel of dishwasher when the rack is pushed in. It has three holes that need thin washers. It doesn’t stay in place anymore.
For model number SHX68T55UC
Hi Pat, thank you for the question. According to our research, the part you are looking for is not sold separately. You would have to replace the tube, part number PS12072215. We hope this information helps!
The E:15 error code means water is detected in the pan under the unit. There are several ways this can happen.
In this case, it was caused by a bad inlet valve. It did not close properly and led to an overflow of water inside that eventually spilled into the pan underneath the unit.
I see now why the pump keeps run
... Read morening after this error. In this case, it would have led to a big flood in the kitchen if it did not.
I was actually able to run the unit while broke by manually operating the valve under our sink that provides water to the unit.
Be sure to turn off breaker before servicing. Don't get shocked!
Be sure to turn off water before starting! Or, you'll have a flood.
Anyway, I just pulled the unit out (was secured by 2 screws on the sides). I lifted up the insulation material on the left side to get at the valve. Pushed a little green tab to release the electrical plug. Then, use pliers to move clamp off the white water hose on the inside. Then, pull of white hose. This was hard in my case. Took a lot of force. Then, reach behind the unit and use pliers to unscrew water hose. Now, the whole gray panel there can pop out with some force. Then, slip the old valve out and slip new one in. Reconnect hoses and clamp. Note that I put some caulk on the connector where white hose goes. Not sure if needed or not.
