Models
>
SHE45M06UC
SHE45M06UC (46) Bosch Dishwasher - Overview
Sections of the SHE45M06UC
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Tine Holder
PartSelect #: PS8712513
Manufacturer #: 00418498
This plastic holder is also known as a tine clip, or a rack flip tine clip. It is used in the lower rack of a dishwasher, it is part of the rack assembly that allows to convert your rack to better the...
$7.59
In Stock
Lower Rack Wheel with Clip
PartSelect #: PS8697067
Manufacturer #: 00165314
This dishrack wheel is designed for use on the lower rack of your dishwasher, it allows the rack to roll in and out of your appliance with ease. This roller wheel includes the locking clip required fo...
$18.55
In Stock
Door Seal
PartSelect #: PS8723143
Manufacturer #: 00494772
This seal is also referred to as a door gasket, and it is designed for use on dishwashers. It is installed on the door of the appliance, and it seals the space between the tub of the dishwasher and th...
$31.10
In Stock
Lower Rack Tine Clip Kit
PartSelect #: PS8714310
Manufacturer #: 00428344
This tine clip kit is designed for use in the lower rack of dishwashers. Some dishwashers have adjustable tines that allow you to convert the rack in your dishwasher to accommodate more dishes, and di...
$39.34
In Stock
Micro Filter
PartSelect #: PS8727803
Manufacturer #: 00615079
This micro filter basket assembly is used in dishwashers. The filter is responsible for filtering the water inside the dishwasher. All of the food and debris particles that are removed from your dishe...
$28.88
In Stock
Water Inlet Valve
PartSelect #: PS8726680
Manufacturer #: 00607335
This is a replacement water inlet valve for your washer. The water inlet valve in your washer connects to the water source and solenoid wires, and ensures the tub has the right amount of water enterin...
$62.65
In Stock
Drain Pump
PartSelect #: PS8729769
Manufacturer #: 00642239
The drain pump ejects the water from the dishwasher.
$137.38
In Stock
Lower Door Seal
PartSelect #: PS8714648
Manufacturer #: 00432490
This door seal, also known as a door gasket, is an authentic manufacturer replacement part for your dishwasher. It is responsible for creating a watertight seal between the tub and dishwasher door and...
$43.16
In Stock
Dishrack Stopper Kit
PartSelect #: PS8697039
Manufacturer #: 00165254
A holder is used in dishwashers, it is known as the dishrack stop kit. This kit comes with both the front and the rear stop, these parts are installed at either end of the rails that the upper rack sl...
$12.03
In Stock
Questions And Answers for SHE45M06UC
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the SHE45M06UC
[Viewing 10 of 10]Leaking
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The door handle cracked near the control buttons - making the appliance use inconsistant
I used clamps to clamp the door together while I unscrewed the front panel from the back. Once the screws were out, I carefully released the clamps holding the two together with my other hand. Once the door was off, I release the control cover - it was a bit tricky b/c I didn't want to break any other pieces. Once that was off, I remov
... Read more
ed the control button covers from the old control cover and installed them on the new one. I then carefully removed the small silver door handle cover from the old one and installed it on the new one. This piece was a bit tricky b/c it could bend and break easily if wrenched too hard. Once that piece was on, I snapped the control cover onto the front door panel - which snapped on very easily. I then re-clamped the front panel to the metal door carefully aligning the screw holes and inserted all the screws. Once they were lightly tightened, I released the clamps and tried the buttons. All worked well and the control panel was fixed.
Read less
Parts Used:
-
Lon from LAWRENCE, KS
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
20 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring assembly on detergent and rinse aid dispenser broke so the sliding lid would not operate
Here are the steps you need to take to do the job properly:
1. turn off electrical circuit breaker to the dishwasher
2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed.
3 ... Read more . unplug the wiring harness to the detergent/rinse aid dispenser
4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser.
5. the unit will pop out toward the inside of the dishwasher
6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in.
7. re-attach the wiring harness
8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job.
9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks.
10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.
1. turn off electrical circuit breaker to the dishwasher
2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed.
3 ... Read more . unplug the wiring harness to the detergent/rinse aid dispenser
4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser.
5. the unit will pop out toward the inside of the dishwasher
6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in.
7. re-attach the wiring harness
8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job.
9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks.
10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.
Read less
Parts Used:
-
Steven from SUWANEE, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
13 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My dishwasher was not draining
With the help of You Tube, this 50 year old Mom got the job done. Not that complicated if you watch the step by step instructions on the Appliance Pro video. My repairman and husband were both determined to just buy a new one but this 20 year old dishwashing genius was just in need of a little repair. Only need a screwdriver, and sli
... Read more
ghtly confusing as wires hook on a little different on new pumps. I suggest watching video the whole way through and then playing it step by step as you do the repair. Worked great for me. Thanks.
Read less
Parts Used:
-
Karen from CRESTON, IA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
10 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!