Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SF315PEKQ0

SF315PEKQ0 Whirlpool Range - Overview

Get Parts and Repair Help for SF315PEKQ0

If you know the range repair part you need, you can browse the list of all parts on the SF315PEKQ0, or you can search by name or part description. You can also find your part by where it is located on the SF315PEKQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for SF315PEKQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for SF315PEKQ0

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.80

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$2.96

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

$38.16

IGNTR-OVEN

This flat style gas oven igniter has ceramic housing and comes with a connector.

$31.06

Temperature Sensor

This temperature sensor is used to measure the inside temperature of a self-cleaning oven. Its 1000-ohm resistance increases with temperature. The sensor has male leads, is 6 inches in length, and comes with 2 ceramic wire nuts. Fault temperature sensors are often responsible for F3 and F4 error messages on an electric range. Furthermore, if you find your oven is too hot, will not heat evenly, or simply will not heat at all, there could be an issue with your temperature sensor and you should look to replace it immediately.

$12.11

Burner Knob

This white knob take a D-shaped shaft. Sold individually.

$16.10

Burner Knob

Sold individually. This knob accepts a D shape shaft.

$7.83

Rear Leveling Leg

Sold individually.

$2.96

Screw (2)

This screw is sold individually.

$6.20

Touch-Up Paint - White

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, ...

$18.60

Front Foot

This adjustable front leveling foot is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F3 Error message

  • Customer: Charles from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 143 of 182 people found this instruction helpful
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru t... read more

our oven would not heat up

  • Customer: sharnette from baltimore, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 74 of 82 people found this instruction helpful
My husband pulled out the stove turned the gas off then he pulled out the part and replaced igniter....it took only about 20 min to do this job it was very easy and prior to us doing ourselves i called a well known company that does home repairs, I also called a few smaller businesses and to replace this part was anywhere from $175- 250 if not more. we are v... read more

mice had made nests in the insulation wrap in the range

  • Customer: Wendy from Red Hook, NY
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 30 of 33 people found this instruction helpful
I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to fix my stove told m... read more