Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This drum support roller is used for square-ported model clothes dryers. This part is sold individually; however, rollers tend to wear at the same rate, so it is suggested that both should be replaced...
This dryer drum drive belt attaches to the motor pully and works the drum as the motor rotates. The belt has a length of 93- 3/6 inches, and wraps all the way around the dryer drum, around a tension p...
If your dryer is noisy, will not tumble, or is leaving marks on your clothes, you may need to replace the drum glide. The drum glide is installed on the front bulkhead either at the top or the bottom,...
The idler pulley wheel helps the belt to rotate the drum in your dryer. If your dryer will not start, will not tumble, or is noisy during operation, the idler pulley wheel may need to be replaced. Thi...
Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do...
This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appli...
The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place o...
This cylinder felt seal is used in dryers and is located between the back of the drum and the rear dryer panel. If your dryer is experiencing any of these symptoms, replacing the felt seal could solve...
This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start, or does not tumble,...
This dryer drum glide pad is an inch long. It is made of a felt material and is used for gas and electric clothes dryers. The dryer drum glide provides a soft surface for the front of the drum glide a...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
9 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Pete
November 27, 2019
Does the belt tension pulley include the spring
For model number SDE3606AYW
Hello Pete, Thank you for the question. The Spring PartSelect Number: PS11742854 is sold separate from the Pulley. Hope this helps!
Hi Tim,
Thank you for your question. The dryer has a capacity of 7.1 cubic feet. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Linda
November 30, 2019
Drum will not turn with a regular load of clothes. Can only put in a few pieces at a time in order for it to turn. Also seems temp is pretty warm but assuming it is because drum is not turning as it should
For model number SDE3606AYW
Hello Linda and thanks for writing.
There are a few parts that you need to check :
Belt # PS11742271 (this is the most likely part in need to be replaced) or the idler pulley # PS11757553. We hope this helps. Please contact us anytime.
S/n 12392801ej: Date of manufacture and specifications?
For model number SDE3606AYW
Hello and thank you for writing.
According to the serial and model number, this product may have been manufactured May of 2004.
For your convenience, we have attached the link to your service manual. We hope this helps. Good luck with your repair.
https://partselectcom.azureedge.net/assets/manuals/B781165D1AA66A8F211E0F63D68C7FCED4EE93AE.pdf
https://partselectcom.azureedge.net/assets/manuals/28CAAC894A26A486A70F96F7DBF4745A7DD4D7BD.pdf
1 person found this helpful.
Was this helpful?
Thank you for voting!
Roger
November 29, 2019
Dryer develops a squalling noise after warming up.
For model number SDE3606AYW
Hello Roger, thank you for writing. You will want to inspect the Drum Support Rollers, part number PS11741913 for wear, as they could be making the noise. You will also want to consider the Multi Rib Belt, part number PS11742271 for your dryer as the cause. I hope this helps!
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared of
... Read moref. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it.
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surface
... Read mores and let dry. I then applied a 2nd coat and let get "tacky" and installed the gasket. You will need an extra set of hands to hold the gasket in place while you stretch it over the the panel. The vent manifold is held in place with 3 phillips screws and was installed in about 10 minutes. The only gripe I had was in the Parts-Select illustrated breakdown they don't tell you the lint screen comes with the manifold assembly, so I bought one of them too. Now have an extra lint screen
Took it out of the box and put it in the dryer. I could not find this part anywhere else but on this website. The item was delivered the next day to my surprise.
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Maytag Dryer")
