Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
RWS216 Caloric Range - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
The flat style oven igniter is also known as a range oven igniter. The function of this part is to glow extremely hot in order to ignite the gas for the oven burner. With this flat style oven igniter,...
This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set ...
This gas oven safety valve ensures that no gas is released until the igniter has received the proper voltage needed to ignite the gas range. This valve has a 3/8 of an inch inlet flare as well as a 3/...
After shutting off the gas and removing the oven door, which simply slid off of the hinges, I removed the oven plate. The ignitor was attached to the manifold. I removed that and noted the wires were attached back behind a hole in the back of the oven. I thought I would have to access them from the back but when I pulled on them I was
... Read more able to reach them from the front. I was surprised to find plastic lugs covering the wire ends, rather than ceramic. I attached the new ignitor wires and reused the plastic lugs, as no ceramic ones came with the new ignitor. I carefully slid the new ignitor back into the cage/shield attached to the manifold and replaced the manifold. I then turned the gas back on and tested the ignitor (which worked perfectly) before replacing the oven plate. The repair took less than 30 minutes, but my wife and I thoroughly cleaned the door and interior while we had it apart. The hardest part was getting the door back on the hinges, but this too was accomplished after several attempts. The oven heats up beautifully now.
After the appliance store told me that the repair would cost about $500 to fix an oven that wouldn't light we didn't have the money to repair it or buy a new one so we went without an oven (only the oven) for almost 1 year. The igniter would glow but the oven would not light. my son found your site online and passed it on to me. It was so
... Read more simple it's almost funny. I opened the oven door and removed the burner cover. Then reached in and removed the three screws that held the igniter in place. Turned off the gas, disconedted it so I could pull the stove out to get behind it. Found the wires to the igniter and undid the 2 wire nuts. Removed the igniter cover from the old one and slid it onto the new one. Be very careful because the igniter is very delicate and be sure to not toucjh the heating eliment. Slid the new part into place, reinstalled the screws, connected the new wires with the old wire nuts, reconnected the gas and turned on the oven. BAM it worked like a charm.
First we removed the oven doors. Then removed the shelf that separates the oven from the broiler, giving us more room to work. At first we thought we needed to loosen the screws around the bracket holding the ignitor, but we realized that the burner needed to be removed. Lifting the burner up from the front gave us the room to pull it
... Read moregently from the back of the oven wall, giving more room to pull the wires connected to the ignitor from the back of the oven wall out and then disconnecting them. Then carefully pulling the ignitor out of the bracket.
Putting the new ignitor in was easy. Carefully sliding it into the bracket, not touching the ceramic piece, connected the electric wires, pushed the wires back into the hole in the back of the oven. Then placing the burner back into place.
We then turned on the gas and the electricity and the ignitor glowed and the burner lit. PERFECT! In the past we've had a repair man come in and this time we saved $100. Even more perfect.
