RVM1335WC001 Hotpoint Microwave - Instructions

Turned out the issue was easily solved by replacing a single, inexpensive fuse.

First off, UNPLUG THE MICROWAVE.

The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.

Above the stove mounted microwave. I dropped the lens cover from under the bulb and tried to remove the bulb. The bulb separated from the base. I tried to remove the base with a pliers and the lamp socket broke. I ordered the parts and dropped the bottom cover of the unit down (5 screws). Removed 1 screww from the lamp socket, unplugged the wires and took it out. Simply replaced socket, fastened bottom cover of microwave, installed new bulb and closed lens cover.

At first I tried to use pliers to unscrew the base,very uncomfortable working position,upside down and backwards(the microwave is installed over the range top)very limited space for your body and arms to manuver and you really cant see the base,all of this took place after the breaker was turned off ofcourse,finally figured out that you can drop the entire bottom housing of the microwave by unscrewing 6 screws and the light sockets are easily accessable once you lower it,take out 1 retaining screw ,remove the entire socket and unscrewed the broken base and replaced the bulbs,I said bulbs,there is no sense in having to replace another bulb in who knows how long since only one had burned out but they were both the same age

Had to take unit off wall and disassemble the main casing.then disconnected the wires from the magnetron.took the mounting nuts off but wasn't able to remove the magnetron until I loosened the transformer out of the way .Then it came out easy.Installed the magnetron ,tightened the nuts,installed the transformer back in, connected the the wires back on and installed the casing on ,screwed the screws and got help to install the unit to the wall again.....Tested the unit before putting back on the wall to make sure it heated....The parts were exac same type and wasn't too hard to do...

Unplugged the microwave first, then removed the screws that hold the cover in place. This gives easy access to the socket. Remove the screws that hold the socket in, unplug old socket, replace with new one and you are back in the light again.

1. Take off bottom panel
2. discon wire from microwave
3. set panel on table
4. unscrew panel cover under metal cover bracket
5. need to do that because screw from cover panel won't let you put in light bulb in round hole in metal cover panel
6. take new socket holder and insert bulb
and screw back on to metal cover bracket after remove bad socket holder and bulb by unscrewing
7. recon wire
8. test before putting back bottom panel
9. screw bottom panel back on.

Over the range microwave. Replaced magnetron. Completely disassemble the case top and bottom.
Remove screws from bottom of HV transformer. Magnetron will not clear without this removal.

Remove nuts with socket from top of Magnetron. Remove thermo unit from old magnetron and attach it to new. Replace and bolt down Mag. Replace and screw in HV transformer. Make sure all wires are reconnected.

Put it back up on the wall. Took about three hours from taking it down from wall and putting it back up.

1. remove microwave from wall
2. remove cover (many screws)
3. remove nuts holding magnetron in place (4)
4. remove magnetron (this is a pain due to the plastic molding used to direct cooling air through the magnetron
5. get new magnetron in place (this was even more fun to find the right angles to tilt to get the magnetron to fit
6. re-tighten the 4 nuts on the magentron
7. put the cover back on
8. put the unit back on the wall.

bonus repair: the display flickered while the magnetron was on (cooking ) prior to the magnetron dying. found a ribbon cable on the control board to the display with an aluminum foil shield that had peeled off (adhesive failure). re-installing the aluminum shield with packaging tape, and the display no longer flickers

The old fuse is perfectly good. The new ones arrived within a day.

After reading some of the comments that others wrote, I decided to order the light sockets along with the replacement bulbs. As predicted, the old light bulbs broke when I tried to remove them - the bulb separated from the base which was still screwed in the socket. After removing the screws that held the bottom panel, I was able to remove the socket assemblies with ease. After inspection of the old sockets, I was glad I ordered new sockets - the old sockets were burned in some spots and very brittle. The parts arrived within a day and a half after I ordered them, but when the parts arrived, one of the bulbs was broken (happened during shipping). I called the office phone number and talked to a really pleasant technician who refunded me the price of the broken bulb and placed an order for a replacement. That was the Wednesday evening before Thanksgiving Day. I got the replacement bulb yesterday (Tuesday) morning - still really quick considering the Thanksgiving holiday. All of the parts are installed and are working excellent. I am definately going to keep their WEBsite for future use, and I'll be letting my friends know about them. Thanks PartSelect, you've earned my business.

First, I waste $65 by calling some "REPAIR" service. They showed at home and charge me that just to tell me
Second, I researched on the web and ordered a part, which was not the issue. I waste abnother $72
Third, I found Part-Select and got the right answer: the Diode was the problem. Ordered the part form Part-Select and it FIxed it !!!

Note: I did not buy a new microwave because this one is mounted on the wall and it will cost me +$800 just the lowest price.

1. turned off electricity -- unplugged the unit 2. removed 3 screws on top of top vent, removed vent screen then I located the little white cylindrical fuse and popped it out with a table knife. Then I popped in the new fuse. Replaced the vent screen and screws -- plugged in the appliance and it is working again.

I ended up breaking one bulb trying to remove a burnt bulb for replacement. We then tried removing the other bulb and it wouldn't come out either. I googled the problem and found PartSelect and an explaination of the problem. Heat from either the stove or the bulbs had fused the bulbs into the sockets. Comments on the problem explained that you just remove the bottome pannel (we had seven screws), unplug the old sockets, insert the new and new bulbs and reattach the panel. It was quick and no problems to correct. We did discover the microwave was on its own breaker, make sure to disconnect or cutoff power to the microwave before you start.

This was a super easy repair job. I couldn't figure out how the lens that covered the light bulb would have cracked and realized it must have been from my contractor when he replaced my stove. I can't prove it, of course, so I am left doing the repairs. The website was very easy to order from and confirm that I had the correct parts as the model numbers tend to change over time.

This did not fix my problem. I've ordered a new microwave.

First off, UNPLUG THE MICROWAVE.

The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.