Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
This metal freezer door key has a cross shape and is approximately 2 inches long. If your freezer door will not stay shut, you can use the key as a quick fix to keep it closed. If your key will not lo...
This is an OEM part that is made of metal and sold individually. The leveling leg is generally used with refrigerators, dryers, freezers, ranges, cooktops, and microwaves. The leveling leg is meant to...
This gate support is designed to support the gate or fence on your vertical freezer. This part is designed for the right-hand side and differs from the left-hand side gate support. Be sure to note whi...
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.
An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only
... Read moreswing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.
Remove lower door hinge only, and door pops out. Then lay door on floor and remove the screws fastening the inner freezer tray & gasket to the door; this is where the cordless drill w/nut driver attachment is handy as there are 30+ screws to remove and an open freezer with all your food gaining temperature. At this point drop the new gask
... Read moreet in the dryer on low heat for 5-10 mins to soften it, regardless of it's condition. Have someone clean the sealing area on the freezer and where you have removed the old gasket on the door while you fit the new gasket in. Renew all rusted screws and smear a little grease on hinge for future protection since the door is off. Remount door and check for leaks, the door should close and seal on it's own WITHOUT pushing. This is where I realised the importance of warming the gasket, I got lucky by passing a blow dryer along the leaking areas with the door closed. Point: When buying a new freezer look for compression of the gasket which is an indicator of a warped door. My freezer is only 5yrs old and I shouldn't be changing the gasket so soon!
