Models
>
RF22NPEDBSG
RF22NPEDBSG Samsung Refrigerator - Overview
Models starting with RF22NPEDBSG
Click on the best match to narrow your results.
- RF22NPEDBSG ( AA-00 ) SamsungRefrigerator (Samsung Rf22npedbsg/Aa-00 Refrigerator)
- RF22NPEDBSG ( AA 0003 ) SamsungRefrigerator (22.2 Cu. Ft. 4-Door French Door Refrigerator)
- RF22NPEDBSG ( AA 0000 ) SamsungRefrigerator (22.2 Cu. Ft. 4-Door French Door Refrigerator)
- RF22NPEDBSG ( AA 0002 ) SamsungRefrigerator (22.2 Cu. Ft. 4-Door French Door Refrigerator)
- RF22NPEDBSG ( AA 0004 ) SamsungRefrigerator (22.2 Cu. Ft. 4-Door French Door Refrigerator)
- RF22NPEDBSG ( AA 0001 ) SamsungRefrigerator (22.2 Cu. Ft. 4-Door French Door Refrigerator)
Keep searches simple, eg. "belt" or "pump".
Handle Mounting Screw
PartSelect #: PS4144145
Manufacturer #: DA61-03734A
This screw, known as a handle fixer, is used to keep the door handles on your refrigerator secure. This screw is a genuine OEM part that comes individually, and simply screws into place in your refrig...
$9.36
In Stock
Freezer Handle Support
PartSelect #: PS4145253
Manufacturer #: DA61-08247A
This freezer handle support is a 2.5-inch by 1-inch white plastic bracket designed to provide support and stability to the right side of the freezer door handle. It is an authentic manufacturer replac...
$41.27
On Order
Temperature Sensor
PartSelect #: PS4138666
Manufacturer #: DA32-10104N
This a genuine OEM temperature sensor, designed for use with refrigerators, and is an individual part. This temperature sensor is responsible for detecting and adjusting the temperature in your refrig...
$31.48
In Stock
HINGE-FRENCH;AW4,PC,COOL
PartSelect #: PS4145262
Manufacturer #: DA61-08305A
This French door hinge is an authentic OEM part used in refrigerators. It is used to provide support and stability to the door allowing it to open and close smoothly. The hinge is vulnerable to wear a...
$15.45
In Stock
Handle End Cap
PartSelect #: PS4158776
Manufacturer #: DA67-02787A
This is the end cap for the freezer door of various Samsung refrigerators. This end cap is made of plastic and features a brushed-metal finish, and simply snaps on or off the end of the freezer door h...
$15.02
In Stock
Refrigerator Evaporator Fan Motor
PartSelect #: PS9603956
Manufacturer #: DA81-06013A
This is an evaporator fan motor for a wide range of Samsung refrigerators. Evaporator fans pull warm air through evaporator coils to cool and maintain the internal temperature of the refrigerator. If ...
$129.53
In Stock
Refrigerator Evaporator Fan Motor
PartSelect #: PS4138377
Manufacturer #: DA31-00146H
This evaporator fan motor is sourced from the original manufacturer for use in refrigerators. It circulates cold air throughout the refrigerator compartment to maintain consistent cooling. If the evap...
$136.42
In Stock
Bi-Metal Defrost Thermostat
PartSelect #: PS4140510
Manufacturer #: DA47-00243K
If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.
$48.01
In Stock
Common Symptoms of models starting with RF22NPEDBSG
[Viewing 4 of 4]Fridge too warm
Fixed by
these parts
these parts
Show All
Door won’t open or close
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Ice maker not making ice
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Evaporator frozen (refrigrator section) and allowing top section to lose cooling
This is the Samsung French door refrigerator style that so many people have complained about freezing up and not cooling the top section. I first changed out the defrost thermostat and this did not correct the problem. I done a quick resistance check on the temp sensor that's mounted on the evaporator itself. The resistance would change w
... Read more
hen holding an ice cube on the sensor so I just assumed it was ok. PLEASE TAKE NOTE: When performing a resistance check on this sensor, make sure your readings match the Samsung temp/resistance chart in their literature. My sensor was way off calibration and was causing the freeze up. Its working as designed now and DW is happy again. Learn from my mistake.
Read less
Parts Used:
-
Richard from GULFPORT, MS
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
47 of 70 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker frosting up, not making ice
After watching a few you tube videos on the Samsung ice maker removal, this repair was not that bad. The key to this repair is PATIENCE!
Unplug your fridge, have a steamer and Phillips & straight screw driver handy. Remove ice bucket, place rags or paper towels in bottom half of ice maker. Fire up your steamer and melt ALL ice befor ... Read more e proceeding! Once all ice is gone, remove one screw to the left on cover for the wiring, remove plastic wire cover , remove screw just below ice maker itself, push locking tab in to release plastic lower tray attached to bottom of ice maker. Once you do this it exposes the refrigerant line (u shaped) under ice maker. If you can still see ice once that plastic cover drops down, yep... more steaming , if you try chip away any remaining ice damage will result to that refrigerant line then it’s game over. Fridge needs to be replaced! Once fully clear of ice , carefully pry that refrigerant line down a bit so it is released from the bottom of ice maker. Do not bend it down too far only enough so it will clear when pulling ice maker out. Un clip yellow electrical connector to ice maker and gently pull the ice maker towards you and down to fully remove. As you are pulling it out be sure refrigerant line does not get hung up. Once removed you may find more ice build up on top of auger assembly. All ice/ frost needs to be gone. Follow u shaped refrigerant line back towards the styrofoam, push one clip on each tube towards the back with the tab facing down! The plastic rectangle trim piece slides off fairly easy. This web page gives detailed pictures on what to expect, as there could be other issues in that ice compartment that need addressed! https://edmondappliancerepairokc.com/samsung-french-door-ice-maker-frosting-up/
Hope this helps, it sure made a difference in mine. The ice maker has been producing ice like never before!
Unplug your fridge, have a steamer and Phillips & straight screw driver handy. Remove ice bucket, place rags or paper towels in bottom half of ice maker. Fire up your steamer and melt ALL ice befor ... Read more e proceeding! Once all ice is gone, remove one screw to the left on cover for the wiring, remove plastic wire cover , remove screw just below ice maker itself, push locking tab in to release plastic lower tray attached to bottom of ice maker. Once you do this it exposes the refrigerant line (u shaped) under ice maker. If you can still see ice once that plastic cover drops down, yep... more steaming , if you try chip away any remaining ice damage will result to that refrigerant line then it’s game over. Fridge needs to be replaced! Once fully clear of ice , carefully pry that refrigerant line down a bit so it is released from the bottom of ice maker. Do not bend it down too far only enough so it will clear when pulling ice maker out. Un clip yellow electrical connector to ice maker and gently pull the ice maker towards you and down to fully remove. As you are pulling it out be sure refrigerant line does not get hung up. Once removed you may find more ice build up on top of auger assembly. All ice/ frost needs to be gone. Follow u shaped refrigerant line back towards the styrofoam, push one clip on each tube towards the back with the tab facing down! The plastic rectangle trim piece slides off fairly easy. This web page gives detailed pictures on what to expect, as there could be other issues in that ice compartment that need addressed! https://edmondappliancerepairokc.com/samsung-french-door-ice-maker-frosting-up/
Hope this helps, it sure made a difference in mine. The ice maker has been producing ice like never before!
Read less
Parts Used:
-
daryl from LAKE MARY, FL
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
CLOSING MECHANISM BROKE IN TWO.
OPENED THE LEFT SIDE REFRIGERATOR DOOR WHERE THE DEFECTIVE MECHANISM WAS. GOT UP ON THE FIRST STEP OF THE STEP STOOL,REMOVED THE PHILLIPS HEAD RETAINING SCREW FROM THE BROKEN PART.PUT THE NEW CLOSING MECHANISM IN PLACE AND RE-INSTALLED THE PHILLIPS HEAD SCREW. STEPPED DOWN FROM THE STEP STOOL AND SHUT THE REFRIGERATOR DOOR.
Parts Used:
-
TERRY from BAKERSFIELD, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
6 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!