Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The range thermostat is also commonly known as a stove, oven, cooktop, or range thermal fuse. This thermostat protects your oven from excessive heating, and will shut the oven heat off if excessive he...
This temperature sensor, also known as a thermistor, is compatible with various makes and types of appliances. This thermistor uses electrical currents to detect the interior temperature of the applia...
This is a genuine OEM leveling leg for various models of LG ranges. This leg is used to stabilize and support the range, and if damaged, broken, or missing, will cause your range to rock back and fort...
This transparent inner door glass is designed for LG range ovens and serves as a key component in maintaining heat insulation while allowing visibility into the oven during cooking. Made from heat-res...
The sub PCB assembly (also referred to as a relay board), is a part for your range. If your oven is overheating, this might indicate that your sub PCB assembly needs to be replaced. You will need a Ph...
This radiant heater may also be known as a radiant surface element and is a part for your range. The function of this heater is to supply heat to the cooking area that is on the top of the range. This...
Enhance your range's performance with this genuine LG AC Fan Motor. Specifically designed for some models of LG Electric Range Convection Ovens, this crucial component helps to circulate hot air evenl...
This radiant surface element is a genuine OEM replacement for select LG electric ranges, designed to generate heat beneath the glass cooktop for a single burner. It ensures fast, even heating for effi...
This oven and range display control board manages key cooking and control functions, acting as the main interface between the user and the appliance. It regulates oven temperature, controls cooking ti...
Got a faulty water filter system? You?ll need our genuine GE Nozzle/Vent Assembly. This isn?t any old part ? it?s what you need to keep your water softener functioning as smoothly as possible. This pa...
I searched online and found someone that seemed to have the exact problem. That person had replaced the lower burner and the same PCB board I replaced. I was able to test the lower burner without removing it and it tested OK. The PCB board in the article I had checked was burned and obviously bad but mine was not. I took a chance and
... Read moreordered just the PCB board. I replaced this board and the oven now works perfectly. I seems this board was not turning on the bottom burner but the system thought it was working fine.
Very easy.1: Shut power to stove. 2: Remove 3 hex screws from oven to range top at underside of top. 3: Raise to from front and disconnect multi- connector at right rear of top. 4: flip over top and demoed 4 screws on hold down strap at each side. 5: Remove element from under strap. 6: Disconnect element from wir
... Read morees./ remember where wires were connected. Connect multi connected from stove. 7: Replace strap and flip top, screw it back on, put power back on. Only about 30 minutes even if you get a coffe break. Don’t even have to move stove.
Removed the back of the Range. Removed one wire at a time from the old PCB and placed it in position on the New PCB. Then secured the New PCB in the holder.
