PP31 Poulan - Overview
Models starting with PP31
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Fuel Line (25" Length)
PartSelect #: PS9008183
Manufacturer #: 530069247
This is the replacement fuel line 25 Inch for several OPE products that use small engines. The fuel line carries fuel from the tank to the carburetor. Over time, the fuel line can become badly clogged...
$12.20
In Stock
Engine Fuel Filter
PartSelect #: PS9285148
Manufacturer #: 530095646
This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this esse...
$9.16
In Stock
Purge Line
PartSelect #: PS9008180
Manufacturer #: 530069216
This is the Genuine Craftsman replacement part. It is made out of Flexible Rubber and is Sold Individually. The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the car...
$18.34
In Stock
Purge Bulb
PartSelect #: PS9003852
Manufacturer #: 530047721
This primer bulb, also known as a purge bulb, is used to push more fuel from the fuel tank into the carburetor of your small engine equipment, to help the engine start easier. Over time and through ex...
$12.20
In Stock
Nut
PartSelect #: PS9004113
Manufacturer #: 530015917
The OEM Mounting Bar Nut is a nut used to install a mounting bar to your machine. Installation requires a wrench set and socket set, and is rated as "Easy". This nut attaches to the chainbar studs.
$6.40
In Stock
Walbro Gasket/Diaphragm Kit
PartSelect #: PS9285128
Manufacturer #: 530069844
This is an authentic OEM replacement kit for use with lawn and garden equipment. Each kit includes the carburetor, cylinder, crankcase, and muffler gaskets. The carburetor gasket seals the area betwee...
$30.58
In Stock
Spark Plug
PartSelect #: PS8996057
Manufacturer #: 503235111
Compatible with over 150 models of lawn equipment, this Spark Plug has been sourced directly from the original manufacturer. It is sold individually, made of metal and ceramic components, and is not p...
$9.16
In Stock
Chain Catcher
PartSelect #: PS9004067
Manufacturer #: 530029850
This is a genuine manufacturer approved replacement part designed for use with chainsaws. This part is an important safety feature because it prevents the chainsaw chain from flying off the bar if it ...
$9.16
In Stock
Adjust Pin-Bar 36/41
PartSelect #: PS9003373
Manufacturer #: 530015826
This Bar Pin Adjuster is an OEM part used to adjust the tension on the bar, which loosens or tightens the chain. It attaches to the slot in the bar, and the chainsaw bar adjusting screw. Installation ...
$7.63
In Stock
Clutch Drum
PartSelect #: PS9007596
Manufacturer #: 530047061
This is a genuine OEM sourced component which is specially made for Poulan and Husqvarna chainsaws. The are two functions of the clutch drum assembly. It encases the clutch and when the engine gets up...
$27.52
In Stock
Air Filter
PartSelect #: PS12607075
Manufacturer #: 545057701
This is a genuine Poulan replacement part, it is sold individually. Its purpose is to filter out dirt and debris from entering the carburetor and engine. Once this filter gets clogged it should be rep...
$7.63
In Stock
Rope Kit
PartSelect #: PS9008182
Manufacturer #: 530069232
The chainsaw starter rope is a three-foot-long white rope that is approved by the original equipment manufacturer, and which wraps around the recoil pulley and is pulled to start the engine. Installat...
$7.63
In Stock
Common Symptoms of models starting with PP31
[Viewing 2 of 2]Will Not Start
Fixed by
these parts
these parts
Show All
Engine stops after a few seconds or minutes
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Both the Fuel line and the Engine fuel line, where dry rotted.
1) While still attached to the fuel tank, I first sized up the old fuel lines with the newer fuel lines.
2) With a pair of needle nose players, I then removed the old dry rotted fuel ?? lines, from the fuel tank.
3) I cleaned the fuel tank and around the carburetor area, to insure that there was no debris, that could possibly fa ... Read more ll into the path of the new fuel lines installation.
4) I then installed the smaller one of the fuel lines, so that it would be out of the way, of the larger fuel line. I Pulled the fuel line through the smaller hole in the fuel tank, with needle nose players. I pulled the smaller fuel line out through the fuel tank filler hole, attached the fuel filter to the smaller fuel line. I Made sure that the fuel filter was extended to the furthest end of the fuel tank bottom. Six inches in all. I then attached the smaller fuel line to the carburetor.
5) I Installed the larger fuel line, followed the same procedures as the smaller fuel line.
6) Both fuel lines where cut on an angle for easy installation. No lubricant was necessary.
7) I filled up the fuel tank with fresh fuel and oil, new air filter and spark plug. It started on the first pull. Amazing.
2) With a pair of needle nose players, I then removed the old dry rotted fuel ?? lines, from the fuel tank.
3) I cleaned the fuel tank and around the carburetor area, to insure that there was no debris, that could possibly fa ... Read more ll into the path of the new fuel lines installation.
4) I then installed the smaller one of the fuel lines, so that it would be out of the way, of the larger fuel line. I Pulled the fuel line through the smaller hole in the fuel tank, with needle nose players. I pulled the smaller fuel line out through the fuel tank filler hole, attached the fuel filter to the smaller fuel line. I Made sure that the fuel filter was extended to the furthest end of the fuel tank bottom. Six inches in all. I then attached the smaller fuel line to the carburetor.
5) I Installed the larger fuel line, followed the same procedures as the smaller fuel line.
6) Both fuel lines where cut on an angle for easy installation. No lubricant was necessary.
7) I filled up the fuel tank with fresh fuel and oil, new air filter and spark plug. It started on the first pull. Amazing.
Read less
Parts Used:
-
Victor from SCOTTSVILLE, KY
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
51 of 67 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
installing fuel through fuel tank wall
To start, remove the plastic carburetor grill. DO NOT remove the carburetor. The fuel line has to be sliced down to fit through the tank hole and get it in far enough up into the tank to grab with needle nose pliers.( need long needle nose pliers which I didn't have) I placed about six inches of the plastic tubing in the jaws of vice so t
... Read more
hat half of the tube was squeezed in the vice jaws. I then used a razor blade to shave off the exposed tube. I slipped the shaved end of the tube up through the tank hole far enough to grab with long tweezers and pulled it up to where I could grab it in the tank with needle nose pliers. I put light lube oil on the remaining tubing and pulled it through. It takes a steady firm pull to pull it in. Install the filter and pull the tube back down into the tank. I also used a small diameter drill bit and with my fingers slightly reamed the tube ends to ease the tube over the filter and carburetor nipples. To prime the engine, spray starting fluid into the carburetor and start. Repeat until the engine will run on fuel. It took me hours to figure this out, but will take less than an hour with this method.
Read less
Parts Used:
-
RICHARD from BROCKTON, MA
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers
9 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Split fuel line driving brother-in-law to frustration
Seven screw, three case cover, two air cleaner, two carb mounting, pulled carb, drained tank, pulled old fuel line, treaded new one in, wire to thread, thread to angle cut fuel line. Reassemble, test, sharpen chain, retest…not exactly a doityourselfer, graduate degree in mechanical/industrial engineering and former medium/heavy mechanica
... Read more
l. Get fuel line on carb prior to reassembly, line may need some stretching with a tapered punch.
Read less
Parts Used:
-
Howard from UNICOI, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!