PIRANHADW General Electric Dishwasher - Instructions

1. Pull out dishwasher (not all the way) 2. Open the door. 3. Remove the white rope holding the door hinge (both sides) 4. Remove the door by pulling up when the door is open about 4-8 inches. 5. Lay the door on the floor ( put something under the door so not to scratch the front. 6. Remove the small bolt at the bottom of the door (both sides). 7. Slide the hinge back, up, then out. 8. Where the hinges were are another set of bolts, remove those (both sides) 9. Grab the top part of the door (the part with the buttons) and slide apart. 10. Remove the styrofoam carefully. 11. Disconnect the wiring harness. 12. Remove the 6 screws holding the Despenser tray in place. 13. Put in new Despenser tray and put everything back together.

Could not do the repair. The incorrect service rack was shipped. It was a different model than what was ordered. It was a different size and would not fit. Had to ship it back at my own expense. Service rack was $77.03 and that has been reimbursed. The return shipping cost to me was $43.75. That expense still has not been reimbursed. I do not want to risk ordering another service rack and risk having to go through the same type of service again.

The part simply snapped in and worked perfectly.

When the part arrived, I was pretty sure it was the wrong part. The replacement part had an LED on it -- a box that stuck up about an inch above the circuit board. My dishwasher did not have an LED readout and I was pretty sure the LED would not fit in the space that was available. I was reluctant to take the dishwasher apart until I had the right part. The people at Part Select were helpful and together we looked at the schematic which did, indeed, seem to show a box sticking up from the circuit board. A YouTube video showed me how to take the door off its hinges, unscrew 4 screws and slide the inside of the door upwards. The circuit board went in fairly easily. There was space for the LED (even though it still doesn't show through the top) and now the lights work.

*Unplug the dishwasher. My drain hose was long enough so no need to disconnect.
Access the motherboard and found a solid green light. This indicates the motherboard is not communicating with the user interface.

Door removal:
- removed kick plate
-unplugged door wire assembly and wire harness clip
-Unscrewed dishwasher from cabinet and pull dishwasher out about 6 inches
-Detached pulley rope assembly from door hinge
-Open door about 4 inches and pull up and towards me.
-Lay the door down, removed vent cap and four T20 screws from the side bottom, remove two 1/4 inch bolt from each hinge(the hinges have four bolts, but only to need to be removed)
-push up on the plastic inner door from outer door and set aside.
-Unscrew four 1/4 inch bolts holding user interface and unplug wire assembly. (The two middle screws are longer than the two outer screws)
-be sure to ground yourself before touching the new user interface board
-read the instructions for the new interface board clip positions(mine was already position correctly)
-Assemble the door and be sure to connect the wire assembly and harness clip.

Took it out of the box and set rollers on track
rolled in place ALL DONE

Had to remove the rubber gasket on the new spray arm to install the device, as it was hard to push into the above slot that fits the arm..

Twist counter clockwise to remove clockwise to install

Popped old bracket off with screwdriver, with a then easy installation of the new part.

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.

-Disabled power.
-1/4” nut driver to take off kickplate.
-Unplug wires harness to door
-Dismount dishwasher from cabinets and pull out 4-6 inches
-uncouple spring pulley from door hinges.
-Open dishwasher door about 4 inches and pull out and up to remove
-Lay door down and remove 4 -T20 star bolts and two 1/4” bolts from door hinges(the door hinge has four bolts, but only remove one from each hinge that connects to the inner plastic door)
-remove vent cap and push up on interior plastic door casing to separate outer and inner door.
-Unbolt the soap dispenser module via 1/4” bolts and replace with new module. (be sure to line up module and gasket properly, installing 1/4inch bolts crossways, slowly tightening each bolt for a perfect seal).
-Reassemble the inner/outer doors and reattach to dishwasher in reverse order.
Be sure to plug the doors electric harness and kickplate.
-Plug the dishwasher back in and run it through a test.

I recently replaced the user interface, which took about 30 minutes. A week later replaced the soap dispenser module, which took 20 minutes. Disassembling the door was easier the second round.

I would read this project very easy for somebody with technical skills and easy with no prior skills

Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.

I replaced the User Control and Display Board and it is working very well now. The important things that should be noted are to take off the door and to open the door cover by unscrewing it. Those screws are located at the bottom of the door and two are hided inside.

Watched YouTube video on how to diagnose problems. Once part was identified ordered from Partselect.com and replaced the user interface circuit board. Dishwasher is now working.

Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.

Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one

2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.