PGT-183UWW (PGT-183UW W) Amana Cooktop - Overview
Sections of the PGT-183UWW
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Dryer Screw
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.47
In Stock
Spark Ignition Module with Bracket
PartSelect #: PS2034431
Manufacturer #: 32020101
This spark ignition module lights the gas that starts the burner on your range or cooktop. This electrode is part of the burner assembly, sits next to the burner head, and is just over an inch in leng...
No Longer Available
Range Installation Screw
PartSelect #: PS11741612
Manufacturer #: WP3400882
This screw is sold individually.
$7.47
In Stock
Refrigerator Screw
PartSelect #: PS11745625
Manufacturer #: WP8281227
This screw is sold individually.
$11.77
Special Order
Single Gas Grate
PartSelect #: PS2029677
Manufacturer #: 305810Y
This part has been redesigned to be darker gray. If you have the older light gray design, you might consider replacing all 4.
No Longer Available
Spark Switch
PartSelect #: PS2181771
Manufacturer #: Y0042053
This switch is used with gas ranges and ovens. The part sits on top of the valve. Once the knob is turned it will create a spark that will light the gas and starts the burner.
No Longer Available
Common Symptoms of the PGT-183UWW
[Viewing 3 of 3]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
2 of 4 burners wouldn't light
Unplugged the stove, removed all 4 burner discs from the stove top (2 screws each) and disconnecting electrode wires as I pulled them out, removed the stove top, unscrewed the old module, removed the 6 wires, connected wires to the new module, screwed it into place, reinstalled the top while poking the electrode wires through the top one
... Read more
by one, put the stove top in place, connected the wires to the burner discs. Done, and it works! It took longer to find and order the part than it did to change it out.
Read less
Parts Used:
-
John from Alexandria, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
25 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spark did not ignite one burner and sometimes two
I could not figure out how to get to the igniter until I went to the "Part Select" web site and found a post that was exactly like the problem that I had. IE: Remove two screws holding each burner, Lift off top, remove old igniter being "Carefull" not to mix up the wires when putting them on the new one, installed new igniter in bracket a
... Read more
nd mounted in position, Reinstalled top and PRESTO - it worked. First post was VERY HELPFUL. Thank you
Read less
Parts Used:
-
Frederick from Eagle, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
14 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The front burners on my Amana stove never sparked reliably and finally stopped working altogether.
I read on this site about someone who had my same problem. He ordered and installed a new spark ignition module and after installation the stove worked fine. So I ordered a part # PS2034431 Spark Ignition Module for my Amana stove. I installed it, and it worked just fine, really for the first time since I bought the stove new. Oh well
... Read more
...
Taking the stove apart took a bit of study to find how to get it right, and the clothes pins were to keep the wires from slipping back through the stove top as I was putting it back on before actually hooking up the piezo units. The instructions that came with the spark igniter were pretty useless (not wrong, just useless), but carefull notes while taking the bad unit out and where each wire went made the replacement rather easy. The really tough part was removal of the burners - the small screws had deteriorated over the last 7 years, so I had to drill two of them out. I replaced all of them with stainless steel screws. This cost an hour of my time plus a trip to the hardware store.
But as I said... the stove now works fine really for the first time. Way to go, Amana!
I trust this igniter will last a lifetime.
And certainly, reading about the same problem I had and easily finding the part was a welcome treat on this site.
Taking the stove apart took a bit of study to find how to get it right, and the clothes pins were to keep the wires from slipping back through the stove top as I was putting it back on before actually hooking up the piezo units. The instructions that came with the spark igniter were pretty useless (not wrong, just useless), but carefull notes while taking the bad unit out and where each wire went made the replacement rather easy. The really tough part was removal of the burners - the small screws had deteriorated over the last 7 years, so I had to drill two of them out. I replaced all of them with stainless steel screws. This cost an hour of my time plus a trip to the hardware store.
But as I said... the stove now works fine really for the first time. Way to go, Amana!
I trust this igniter will last a lifetime.
And certainly, reading about the same problem I had and easily finding the part was a welcome treat on this site.
Read less
Parts Used:
-
Arthur from Vinalhaven, ME
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!