Models
>
PGP7030DL2BB
PGP7030DL2BB General Electric Cooktop - Overview
Sections of the PGP7030DL2BB
[Viewing 3 of 3]Keep searches simple, eg. "belt" or "pump".
Burner Grate Foot
PartSelect #: PS11729077
Manufacturer #: WB02X24790
This burner grate foot, also known as a bumper, is an authentic OEM replacement part for your range. It is a small black rubber component that acts as a buffer between the metal grate and the surface ...
$13.13
In Stock
Burner Cap - Black - Medium - 9500 BTU
PartSelect #: PS954202
Manufacturer #: WB29K10023
This burner cap is for your gas range, and acts as a cover for the burner head. It is black in color and just over 3 inches in diameter. If your old burner cap is damaged or missing, this is the part ...
$30.19
In Stock
Burner Cap
PartSelect #: PS954203
Manufacturer #: WB29K10024
This is a burner cap for your gas range. The cap acts as a cover for the burner head. If your old burner cap is damaged or missing, this is the part that will replace it. The cap is black in color and...
$21.00
In Stock
Burner Cap - 15K
PartSelect #: PS954107
Manufacturer #: WB28K10222
This is a replacement burner cap for your gas range or cooktop. The burner cap is found on the burner head, and prevents debris from getting into the head when it is not in use. The cap is black in co...
$34.50
In Stock
Economic Nut
PartSelect #: PS951649
Manufacturer #: WB01K10037
This economic nut is a manufacturer-approved replacement part for your oven range. The nut can become worn down or stripped over time and need replacing. Make sure to disconnect power to the unit and ...
$8.06
In Stock
Questions And Answers for PGP7030DL2BB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Original burner cap was chipping; must have been dropped somewhere along the line.
New burner cap replaced old; just placed over burner; no tools required.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
Parts Used:
-
Mitzi from Briarcliff Manor, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
8 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing grate foot / bumper
-
Irene H from HENRICO, VA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
6 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electrode would produce spark to lite burner
The following are steps in replacing a burner electrode for GE Profile Cook Top Model PGP7030DL1BB
1. Shut off gas and unplug electrical plug
2. Remove all stove grates and turn on knobs
3. Remove all burner covers
4. Remove all screws [three for each burner]
5. Remove two screws near front by removing rubber gra ... Read more te grommets
6. Carefully Lift off stove cover and set aside
7. Remove shield near back of stove top. This exposes all burner wires
8. Remove electrode to burner which does not lite by sliding out clip at bottom of electrode—note color code of wire and replace with same. Change one electrode at a time to insure wire color code is correct.
9. Reassemble in reverse order of steps 1-8
HAVE A NICE DAY
1. Shut off gas and unplug electrical plug
2. Remove all stove grates and turn on knobs
3. Remove all burner covers
4. Remove all screws [three for each burner]
5. Remove two screws near front by removing rubber gra ... Read more te grommets
6. Carefully Lift off stove cover and set aside
7. Remove shield near back of stove top. This exposes all burner wires
8. Remove electrode to burner which does not lite by sliding out clip at bottom of electrode—note color code of wire and replace with same. Change one electrode at a time to insure wire color code is correct.
9. Reassemble in reverse order of steps 1-8
HAVE A NICE DAY
Read less
Parts Used:
-
terry from NAPLES, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!