Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
PDT760SSJ7SS General Electric Dishwasher - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This lower rack roller is a genuine replacement component designed to support the smooth and stable movement of the dishwasher’s bottom rack. Measuring approximately 1.5 inches in diameter and finishe...
This dishwasher door latch is designed to secure the door during operation by connecting to the door strike and ensuring a tight seal. Mounted to the tub frame, it plays a critical role in enabling th...
This is a flood switch assembly for your washer. The flood switch controls the hot and cold water filling your washer tub to ensure the proper amount of water. You may need to replace this part if you...
- Includes: 4 brackets, 4 roller wheel brackets, and 8 wheels part # WD12X26146
Dishwasher Lower Dishrack Carrier and Roller Kit (Set of 4). This kit will replace all four one piece roller carriers w...
This mounting bracket is manufactured to secure your dishwasher to your countertop. Mounting brackets should be installed so the dishwasher doesn’t tip forward. You can fit the bracket to either the c...
This OEM-compatible screw is designed for use with many GE dishwashers. Measuring 8-16 HXW and 1/2" in length, this stainless steel screw secures the middle spray arm hub to the upper rack assembly, e...
Stop leaks and keep your dishwasher running smoothly with this tub gasket replacement. It forms a tight seal between the door and tub, so water stays inside during every wash cycle. Made from strong, ...
This dishwasher latch strike is a manufacturer-approved replacement part for your appliance. The latch strike is an important component in your dishwasher door assembly, and adds an extra layer of sec...
This part is a replacement middle spray arm bearing for your dishwasher. The spray arm bearing reduces friction and allows the spray arm to rotate during the operating cycle. If the spray arm is not r...
Upgrade your GE dishwasher with this essential Lower Rack Clip. This durable tine row clip holds the tine row in its proper position, ensuring smooth and efficient operation. Specifically designed for...
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
William
January 18, 2020
Water keeps leaking back into the dish washer after the cycle ends and dish washer is empty.
For model number PDT760SSJ7SS
Hello and thank you for writing.
There is usually a check valve PS11762952 that goes from your sink to the dishwasher. This valve may be faulty. This also may be because the impeller PS11736583 has become worn down from continued use and cannot seal the area which acts similar to a check valve, therefore, letting drain water back into the dishwasher. We hope this helps. Please contact us anytime if you require further assistance.
Dishwasher door falls when opened which is very dangerous. Are there replacement springs that can be ordered ?
For model number PDT760SSJ7SS
Hello and thank you for writing.
Yes, the spring PS8768365 can be ordered, you might want to check your door cable assembly PS9494475 for the door to make sure this is not damaged. We hope this helps. Please contact us anytime if you require further assistance.
We tried cleaning out the filter and it clogged with a huge amount of gunk. We removed the gunk, scrubbed the filter, and tried running the dishwasher, but still no water. That took over an hour (not counting the time the dishwasher spent running). Then we tried your diagnosis center and it pointed to the flood switch or the water valve.
... Read moreI extracted the flood switch (another 30-60 minutes) to check it, and it also contained gunk and (significantly) did not rattle, which made me suspect the flood switch was the problem, so I ordered one. Once the replacement arrived, I checked it and the flood switch rattled, confirming that it should work properly. I spent 30-45 minutes installing it, plus the filter assembly and racks I had to remove to access it. Ran the dishwasher and everything came out sparkling clean. I don't know where the gunk came from, but if you aren't getting water and the filter is full of gunk, check the flood switch.
Ran the diagnostic code test and no alarms turned on. Ran the heater test and it didn't turn on. I figured it was either the flood switch or the heating element itself. Removed and cleaned the flood switch and still nothing. Replaced the old flood switch and now it works like a charm. It took a minute to run tests and figure out a pl
... Read morean of action, but after ordering and receiving the part it was a quick operation to replace the old flood switch. Kill the power. Remove lower basket. Remove lower arm. Remove the coarse filter and the fine filter. Dry up water in bottom of dishwasher. Use 1/4" nut driver to remove two screws holding flood switch in place. Unplug old switch. Plug in new one. And put everything back. Saved a few bucks for sure. If I can do it, you can do it!
1. Turn off breaker supplying power to dishwasher in electrical panel 2. Open dishwasher door 3. Unscrew the screws that secure the dishwasher to the counter. 4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch. 5.
... Read more On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside. 6. Remove old door latch. 7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in. 8. Plug wire harness into new door latch. 9. Re-align dishwasher and re-secure to counter in previous position. 10. Test latch to make sure it closes properly. 11. Turn on breaker in electrical panel. The dishwasher should now function properly.
