Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
PDS22SFSDRSS General Electric Refrigerator - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This sensor (Temperature Sensor, Thermistor, Refrigerator Temperature Sensor) sends the temperature reading of the compartment to the control board. If you notice your refrigerator is too warm, too co...
This 40-Watt light bulb is sold individually.
It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges,...
The water inlet valve on your refrigerator allows water to enter the ice maker and water dispenser. If your ice maker or water dispenser is not functioning properly, or you notice a leak, you may need...
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. This part has been updated by the manufacturer and may appear different t...
This heavy-duty cord has a three-pronged plug (2 electrical, 1 grounding). The power cord supplies power to your refrigerator, allowing it to keep the contents inside cool. There could be an issue wit...
The fan blade is not included. This motor operates the fan to help circulate the air for cooling of the compressor and the coils. It also helps to evaporate the excess water located in the drain pan.
I went to a GE repair center to explain my problem, the service center reccomended that I have a techinician come out o look at it. $75.00 for the visit and what ever labor and materials wuld cost.
I went on line to see if there were others having this same problem and found that there were many with the same problem.
... Read more />After reading some of the ways that people found out what was wrong ...it became a matter of three components, the timer, heater or thermostat.
I tried the most common component and the less expensive one first , the thermostat switch I installed it very easily snipping two wires and attaching the news using wire nuts I used the diagram on this website to pinpoint the component and there has not been a problem since.
First, unplug the refrigerator. Next, remove the lower panel on the back of the refrigerator that covers the compressor, condenser and fan compartment. Looking at the refrigerator from the back, the condenser fan is at the lower right corner. There is no information about removing the fan motor, so it took a bit of study. It became
... Read moreobvious that the plastic fan venturi (panel with hole in it for fan blade) needed to be removed. There were two screws that held the venturi panel in place. After removing these screws the top half of the venturi panel could be bent down and pulled from the cabinet. Note that there are tabs and slots on the bottom of this panel that will need to be matched up when replacing the panel. Next the fan blade needed to be removed. This is done by pulling firmly on the balde and it separated from the motor shaft. The most difficult problem was to remove the motor from the motor bracket. There is very little room to remove the two phillips head screws from the front of the bracket, so I used a socket ratchet wrench with an adapter that would hold a phillips bit. This allowed me to remove the screws which were at a right angle to the wrench handle. It took quite a few incremental ratchet movements to remove each screw. After the screws were removed, the motor and wire could be removed by prying the plastic motor bracket apart. There is a insulated cover that is tie wrapped over the motor plug. This was removed and the plug was removed. The steps were reversed to install the new motor. Be sure the venturi panel is positioned correctly and that the fan blade is pushed firmly onto the motor shaft.
