PDP755SBV1TS General Electric Dishwasher - Instructions

I found it online! There were step by step instructions that were easy to understand. I have never had to do anything like this in my life, only recently had to start doing everything around the house myself due to husband's illness.
The repairman came out, charged me $100 to determine what the dishwasher needed & left me with the part number. He was going to charge me $389 to install the part and they were over charging for the part. The repairman suggested I just get a new dishwasher.
I ordered the part from the website at 1/2 the price that the other place charges and found it on line. With the step by step instructions and the online page, I successfully installed it MYSELF. Saved me a ton of $$.
I LOVE the website
Thank You!!!!

It was a simple as: attach and done!
There is a ring on the part that tightens clockwise to the nipple that sprays out the water that it rests on. Twist clockwise and you are done!
It is a mystery how it was unattached to begin with but not a problem in the end, it was easy to fix!

Thanks for sending genuine GE parts!

Replaced floating seal. Un plugged and Pulled washer out from the counter and laid on its left side. Pull pump out of seal by hand. Straight screwdriver to lever seal out of fitting. Clean hole and wipe seal then push into hole. Reinsert pump reverse install.
To make it easier I previously extended the water supply hose to nearly 8 feet so did not have to disconnect it.

Replaced bad roller carrier with a new one.

Removed old spray arm. Installed new one. New model spray arm doesn’t need metal heat shields.

There was no repair -- it was a simple snap-in replacement of lower spray arm assembly. The shaft holding the lower spray arm in place is plastic so of course it broke when a utensil blocked the arm from spinning.

I appreciate the Parts Select company for enabling me to purchase a replacement part though that allows me to keep my old dishwasher working.

Process of elimination and a visit to my local repair store told me it was wise to try the tub gasket, and according to partselect.com, it solved the problem a majority of the time. My local repair dealer agreed: Try it. They agreed because for them to replace a lower door gasket AND the $10 tub gasket... if they came out, the service call and parts would equal half the cost to replace the whole dishwasher. So I bought a tub gasket from partselect.com and replaced the old one. It worked, it was easy, so if your same make & model is leaking? Try it first. That's my advice.

1) Pull out lower basket plate holder out. Now would be a good time to check roller wheels. 2) Grasp lower spray arm base (knurled collar on base) and turn counter clockwise to release. 3) Install new spray arm and turn knurled collar on base clockwise to lock it in. 4) Reinstall lower basket plate holder.
* Done *

Opened the door, put arm on bottom, slid in and twisted. Very, very easy. The right part means a lot. Thank you very much. “ Ol Stump”.

Replaced old gasket with new one. More difficult than expected, because new gasket was much stiffer than old one. Also, the yellow centering spot on gasket (to line up with top latch) was nearly impossible to see. Unfortunately, this did not solve the problem for me, so money was wasted. Bought new dishwasher.

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.

Simply put it on and twist it to lock in place. Took all of 3 seconds

the design of this part is easy to break when closing the top rack.

there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher

the part broke when closing the rack [a dish too tall hit it]

it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

Replaced lower spray arm.easiest repair ever saved tons of money doing it myself