Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this esse...
This Fuel Line is a 25-inch, clear, plastic line used to deliver fuel. It requires a screwdriver, pliers, socket set, and nut driver and is rated as "Easy" to install by customers. If the fuel line we...
This purge bulb is an authentic OEM part from Craftsman for gas blowers, trimmers, blowers and weed wackers. This part disperses fuel to the carburetor to provide starting the blower faster. You will...
This flywheel is an authentic manufacturer replacement part for use with lawn and outdoor equipment. The flywheel is a heavy, circular disc that has magnets that create an electric charge sent to the ...
This metal ring in your engine, known as the piston ring, seals the gap between the piston and cylinder wall. It makes sure that the gases produced during combustion do not escape and that the engine ...
This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams f...
This is a genuine Poulan replacement part, it is sold individually. The purpose of the 530038682 Trigger is to control the speed at which the spool and line rotates on the model shown below. It is con...
This genuine replacement screw is a high-quality OEM part designed for use with Paramount and Poulan gas-powered lawn and garden equipment. It is specifically engineered to secure the starter rope wit...
This is a Manufacturer Approved replacement kit used on a variety of Gas Trimmers/Pruners. This gasket set includes the major gaskets to replace when rebuilding the engine. Its purpose is to make an a...
This is an original Craftsman replacement part. The screw is designed by the manufacturer for use in yard tools such as trimmers, blowers, and brushcutters. This part is made of metal, and is genera...
This is an Authentic OEM fuel tank assembly commonly used on Gas Trimmers. It is made out of Plastic and it includes the fuel lines, fuel cap, and fuel filter. It is very important to replace the fuel...
This is an original replacement part manufactured for outdoor power equipment. The cylinder is used to house the piston and spark plug and is used to provide a combustion chamber to ignite the air-fue...
$17.13
Special Order
Questions And Answers for P3500
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Remove the 4 screws holding the rear motor casing. Then you can take the easy route and drill through the front motor housing with a 3/8 to 1/2 bit in order to access the front muffler screw. If you want to work harder you must remove the motor from the shaft, remove the clutch assembly (this requires a long 15t torx bit, removing the spa
... Read morerk plug to stuff the piston with rope or rag to seize up the piston, and then removing the front motor casing to access the front muffler screw). Once you access both muffler screws remove them with the t20 torx driver. Install the new muffler with the small gasket inside the housing, and the larger gasket/heat shield between the muffler and the motor.
