Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this esse...
This genuine fuel tank assembly is an original replacement part sourced directly from the manufacturer and is commonly used in Craftsman trimmers and weedwackers. Made from high-quality plastic for du...
This Fuel Line is a 25-inch, clear, plastic line used to deliver fuel. It requires a screwdriver, pliers, socket set, and nut driver and is rated as "Easy" to install by customers. If the fuel line we...
The Fuel Cap with retainer, often simply known just as the fuel cap, keeps fuel from splashing out of your tank and debris from entering it. Black in color, it is sold individually and made of plastic...
This purge bulb is an authentic OEM part from Craftsman for gas blowers, trimmers, blowers and weed wackers. This part disperses fuel to the carburetor to provide starting the blower faster. You will...
This flywheel is an authentic manufacturer replacement part for use with lawn and outdoor equipment. The flywheel is a heavy, circular disc that has magnets that create an electric charge sent to the ...
This is an Original Manufacturer Approved replacement part. This part is made out of Foam and it is sold individually. The purpose of the filter is to keep dust and debris from contaminating the carbu...
The Starter Spring is a metal spring used to restract the rope after you pull it to start the engine. Installation of this OEM part is rated as "Medium" difficulty and requires a screwdriver, nutdrive...
This metal ring in your engine, known as the piston ring, seals the gap between the piston and cylinder wall. It makes sure that the gases produced during combustion do not escape and that the engine ...
This ignition module is a genuine OEM sourced item, it is not an aftermarket imitation. Ignition module supplies electric current to the spark plug. If the ignition coil is defective, the engine may n...
This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams f...
This is a genuine Poulan replacement part, it is sold individually. The purpose of the 530038682 Trigger is to control the speed at which the spool and line rotates on the model shown below. It is con...
No Longer Available
Questions And Answers for P1500
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Remove the 4 screws holding the rear motor casing. Then you can take the easy route and drill through the front motor housing with a 3/8 to 1/2 bit in order to access the front muffler screw. If you want to work harder you must remove the motor from the shaft, remove the clutch assembly (this requires a long 15t torx bit, removing the spa
... Read morerk plug to stuff the piston with rope or rag to seize up the piston, and then removing the front motor casing to access the front muffler screw). Once you access both muffler screws remove them with the t20 torx driver. Install the new muffler with the small gasket inside the housing, and the larger gasket/heat shield between the muffler and the motor.
