NX58M6650WG (AA-00) Samsung Range - Overview
Sections of the NX58M6650WG
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Micro Door Switch
PartSelect #: PS4131192
Manufacturer #: 3405-001034
This door switch, also known as a safety switch, is a genuine OEM replacement part for microwaves. It is a safety mechanism that sends signals to the microwaves control system, telling it when the doo...
$32.63
On Order
Oven Burner Igniter
PartSelect #: PS4241428
Manufacturer #: DG94-00520A
This is an oven burner igniter made for use with Samsung ovens. This oven burner igniter is designed to ignite the gas that flows into it, to produce heat. However, over time and with further frequent...
$240.51
In Stock
Leveling Leg
PartSelect #: PS4240934
Manufacturer #: DG61-00525A
The Black Leveling Leg from Samsung is a durable, genuine part designed for use with many Samsung kitchen appliances. This quality leg-leveling device offers an easy-to-use design to correct uneven su...
$37.91
In Stock
Rubber Cushion
PartSelect #: PS4241222
Manufacturer #: DG73-00003A
This rubber cushion is supplied by the original manufacturer and has a shaft approximately 1 inch long. The cushion acts as a layer of protection between the oven door and oven frame/cavity. It preven...
$7.47
In Stock
Left Rear Burner Cap - Black
PartSelect #: PS4240973
Manufacturer #: DG62-00070A
Enjoy the precision and durability of Samsung with this high-quality Left Rear Burner Cap. Known as the "surface burner cap", this essential component is designed to cover the surface burner of your S...
$74.08
In Stock
Bottom Floor Panel
PartSelect #: PS4240944
Manufacturer #: DG61-00570A
This oven cavity floor coating or bottom floor panel is an authentic OEM part supplied by Samsung to ensure compatibility with various models of Samsung ranges. It is a protective layer that sits on t...
$166.48
On Order
Wire Rack
PartSelect #: PS12721757
Manufacturer #: DG75-01001D
This stainless steel wire rack is a sturdy platform for baking or roasting food, making sure heat circulates evenly. It measures approximately 7/16 inches by 24 3/4 inches and is usually found inside ...
$142.84
In Stock
Burner Head
PartSelect #: PS5576948
Manufacturer #: DG62-00076B
The Samsung Burner Head (Aux) is a top-notch enhancement for your Samsung range. Specifically designed to endure high temperatures, this quality part, crafted from sturdy metal, ensures durability and...
$63.64
In Stock
Range Surface Burner Cap
PartSelect #: PS4240971
Manufacturer #: DG62-00067A
The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
$87.98
In Stock
Bake Igniter
PartSelect #: PS11720750
Manufacturer #: DG94-01012A
The bake igniter is responsible for igniting the gas to light the bake burner within the range. Ensure safety precautions such as shutting off the house circuit breaker and gas supply. Tools Required:...
No Longer Available
Burner Head
PartSelect #: PS8764922
Manufacturer #: DG62-00074C
Introducing the robust Samsung Right Burner Head, a full-length surface burner designed especially for Samsung ranges. Manufactured from hard-wearing metal, this genuine OEM item ensures exceptional d...
$85.94
On Order
Hexagon Nut Cap
PartSelect #: PS4133540
Manufacturer #: 6021-001211
This hexagon nut cap, also known as a nut cover cap, is a nylon-insulated cylindrical cap with left-hand threads and a 4mm thread size, for counterclockwise tightening. It is sourced from the original...
$18.22
In Stock
Questions And Answers for NX58M6650WG
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mark
April 10, 2023
Why Would fire shoot from the controle knob?
For model number NX58M6650WG
Hi Mark, thank you for reaching out. This is probably due to gas leakage. We recommend you check the connections of the tubes. We hope this helps!
Did this question help you?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the NX58M6650WG
[Viewing 7 of 7]No heat
Fixed by
these parts
these parts
Show All
Doesn’t shut off
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Won’t turn on
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven not heating and holding temp
The Samsung stove I have has had the igniter replaced several times. It seems to wear out over a couple years time. I did the repair with a Philips #2 screw driver. Open the oven door, remove the grates. unscrew the bottom cover and expose the heat shield. Unscrew the heat shield. This exposes the burner. Unscrew the burner from the c
... Read more
enter of the plate/lower heat shield. Unscrew the burner from the front and back of the oven. Carefully lift up the burner to expose the igniter and clip. Unscrew the igniter from the burner and set the burner aside. Unclip the igniter from the power cable. If it falls below, it won't go far just reach in a lift it back up to fasten the new igniter to the power clip. Refasten to the burner with new clips and screws provided. Re-insert the burner to the gas jet that is below the bottom plate which will not be visible to you unless you place your head towards the rear of the stove and look down. Once the Jet is back into the hole of the burner, re fasten it to the middle back and front of the stove. Replace the covers and grates. Close the oven and test it. A new igniter does wonders. You can remove the stove door for a less intrusive install, but I found it unnecessary to do so and saved a step and time. I was done well under 30 minutes.
Read less
Parts Used:
-
John from EAST QUOGUE, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
21 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating element needed replaced
First we unplugged the oven and shut off the gas. We then began removing the two plates on the floor, inside of the oven, to reveal the pipe with the dead heating element. You remove the screws from the back of the first plate, pop it out from the front, then remove the screws from the front of the second plate and pop it out from the bac
... Read more
k.
The only issue we encountered was when we attempted to remove the two screws for the pipe: the front screw was stuck (possibly from old oil) and stripped easily. to fix that, we took a metal handsaw, and sawed a new cut into the screw to fit a flathead.
After dealing with the screw, we removed the pipe and unplugged the old heating element. We removed the bottom drawer for extra room to assist with unplugging the heating element, and for removing the pipe from the gas line.
We removed two screws with nuts that were attaching the element to the pipe, and replaced it with the new element.
after reattaching the element and placing the pipe back onto the line, before we placed the plates back, we turned the oven and gas back on to test if it was working. One successful test later, we placed the plates and bottom drawer back and we were done.
The only issue we encountered was when we attempted to remove the two screws for the pipe: the front screw was stuck (possibly from old oil) and stripped easily. to fix that, we took a metal handsaw, and sawed a new cut into the screw to fit a flathead.
After dealing with the screw, we removed the pipe and unplugged the old heating element. We removed the bottom drawer for extra room to assist with unplugging the heating element, and for removing the pipe from the gas line.
We removed two screws with nuts that were attaching the element to the pipe, and replaced it with the new element.
after reattaching the element and placing the pipe back onto the line, before we placed the plates back, we turned the oven and gas back on to test if it was working. One successful test later, we placed the plates and bottom drawer back and we were done.
Read less
Parts Used:
-
Danielle from GIG HARBOR, WA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't light
1) Remove oven door
2) Remove oven floor with Phillips screwdriver.
3) Remove igniter with screwdriver and wrench
4) Remove bottom burner
5) Install new igniter to burner
6) Replace burner
7) Replace oven floor
8) Replace oven door
9) Test
2) Remove oven floor with Phillips screwdriver.
3) Remove igniter with screwdriver and wrench
4) Remove bottom burner
5) Install new igniter to burner
6) Replace burner
7) Replace oven floor
8) Replace oven door
9) Test
Parts Used:
-
Timothy from WASHINGTON, DC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
5 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!